Cisco AnyConnect VPN Client and ASA v8

Error

Title: Cisco AnyConnect VPN Client
Text: An error was received from the secure gateway in response to the vpn negotiation request, contact your network administrator
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------

The website itself says

Connection Established
The Cisco AnyConnect VPN Client has successfully connected.
The connection can be controlled from the tray icon, circled in the image below:

But it lies its not connected.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------


: Saved
:
ASA Version 8.0(2)
!
hostname ciscoasa
enable password 6F9WTj1TxzG5ntGC encrypted
names
name 172.254.1.2 Server
!
interface Vlan1
 nameif inside
 security-level 100
 ip address 172.254.1.1 255.255.255.0
!
interface Vlan2
 nameif outside
 security-level 0
 ip address 10.1.100.254 255.255.0.0
!
interface Ethernet0/0
 switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passwd 2KFQnbNIdI.2KYOU encrypted
ftp mode passive
access-list inbound extended permit tcp any interface outside eq 3389
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool ANYWEBVPN 172.254.254.1-172.254.254.100 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-602.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface 3389 Server 3389 netmask 255.255.255.255  dns
access-group inbound in interface outside
route outside 0.0.0.0 0.0.0.0 10.1.0.254 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 10.1.0.0 255.255.0.0 outside
http 172.254.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
no crypto isakmp nat-traversal
telnet timeout 5
ssh 10.1.0.0 255.255.0.0 outside
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!

threat-detection basic-threat
threat-detection statistics access-list
!
class-map inspection_default
 match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
 parameters
  message-length maximum 512
policy-map global_policy
 class inspection_default
  inspect dns preset_dns_map
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect rsh
  inspect rtsp
  inspect esmtp
  inspect sqlnet
  inspect skinny  
  inspect sunrpc
  inspect xdmcp
  inspect sip  
  inspect netbios
  inspect tftp
!
service-policy global_policy global
webvpn
 enable outside
 svc image disk0:/anyconnect-win-2.0.0343-k9.pkg 1
 svc enable
group-policy DfltGrpPolicy attributes
 vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
username user password A5XOy94YKDPXCo7U encrypted privilege 0
username user attributes
 vpn-group-policy DfltGrpPolicy
tunnel-group ANYWEBVPN type remote-access
tunnel-group ANYWEBVPN general-attributes
 address-pool ANYWEBVPN
prompt hostname context
Cryptochecksum:5dd0eeeb21853583f6f9e360d432c108
: end
asdm image disk0:/asdm-602.bin
no asdm history enable

Note above was done with the wizard - I was curious that there was no nat 0 in the config so I added

access-list nonat extended permit ip 172.254.1.0 255.255.255.0 172.254.254.0 255.255.255.0
nat (inside) 0 access-list nonat

but it gives the same error :(

So I removed it again