asked on

Cisco Router 2600: can not connect

Hi,

1) I have a lab
2) It is a configuration of the Cisco Router 2600
3) The existing configuration:
- There are Native VLAN (Vlan 1), VLan 10 and Vlan 20
- Please see the attached files
4)The IP of the VLAN 1 is 192.168.1.33 (SM: 255.255.255.224)
- So, This VLan 1 is located at Subnet: 192.168.1.33 - 192.168.1.62
5) I setup a PC, and give the IP within the above subnet; the setup is as the followings:
- IP address of the PC: 192.168.1.34
- The SM: 255.255.255.224
- The Default Gateway: Blank
- The DNS: 192.168.1.34
6) My Goal: I want to get connection between the PC and the Router (I connect the PC and the Router with the cross-over cable)
7) Problems:
- When I open the Command prompts ...
- I ping the Router --> I ping 192.168.1.33 ...
- It does not work; no connection
8) I attach the existing configuration of the router
9) Any help?
10) Thanks

tjie
Existing.doc

ASKER CERTIFIED SOLUTION

Les Moore

membership

This solution is only available to members.

To access this solution, you must be a member of Experts Exchange.

Start Free Trial

tjie

ASKER

I am not used to with ios command; i just want to make sure that this ones that you mean:

R1(config)#interface ethernet0/0.1
R1(config-if)#encapsulation dot1q 1 native
R1(config-if)#no ip address 192.168.1.33 255.255.255.224
R1(config-if)#exit
R1(config)#no interface ethernet0/0.1
R1(config)#interface ethernet0/0
R1(config-if)#ip address 192.168.1.33 255.255.255.224
R1(config-if)#half-duplex?
R1(config-if)#end
R1#copy run start (Does this command to Save the configuration?)

Post it back again please

Les Moore

>R1(config-if)#half-duplex?
Upon re-reading your existing config, you may want to set this to duplex auto
R1(config-if)#duplex auto

The rest of it is OK.

tjie

ASKER

lrmoore,

1) It is possible that the above configuration does not have "No Shutdown"?
2) Is it related to Protocol? explain a little bit related to it Please
3) How to check whether the configuration has got "No Shutdown?"
4) Thanks

tjie

Les Moore

1) you will not see "no shutdown" in the config
2) it is related to administratively enabling or disabling the entire port
3) R1#show ip interface brief
Here's an example with one interface shutdown and all others "no shut". They should show "up / up"

Loopback0 192.168.124.1 YES NVRAM up up
Loopback1 192.168.125.1 YES NVRAM up up
Loopback2 192.168.125.2 YES NVRAM administratively down down

tjie

ASKER

lrmoore,

1) This is starting to get interesting ..

2) When i execute the above commands "show ip interface brief"

3) The results are as the followings:

Ethernet0/0 unassigned Yes NVRAM UP UP

Ethernet0/0.1 192.168.1.33 Yes NVRAM UP UP

Ethernet0/0.10 192.168.1.65 Yes NVRAM UP UP

Ethernet0/0.20 192.168.1.97 Yes NVRAM UP UP

4) So, if i just follow your direction above, it should work, right? (I mean i could get the connection between the PC and the Router; then, i can copy the flash from the router to the PC with the help of tftp server)

5 Any other guidance (related to this) is welcome and appreciated

6) Thank you

tjie

Les Moore

Yes, executing the commands I've posted should get you working.

tjie

ASKER

Yes, It works
Thank you very much