Does anybody know a way to reset the admin password on linksys routers without reseting the router to factory defaults? When we purchase a new office we need to know how the internet is confi...
I have a Cisco 871 router that I've been trying to setup for about 5 hours now with no luck. I've read everywhere I could find on the net for instructions. I've used the gui interface, the IOS...
Hi guys,
I am really starting to tear my hair out here. Hope you can help.
I setting up a Cisco 2821 Call Manager Express router with an NM-CUE (Unity Express) module. I have a couple of...
I cannot log into a d-link wbr-1310 wireless router that I just installed. Its asking for a password, Neither adnin or "bank "works.
I have a static IP adress at home, and have set up a domainname (www.domainname.com) pointing to it. I need the router to forward all requests on port 80 to my local webserver.
I have troub...
Dear Experts,
I have a WRT54G model with firmware version 7 on it. Now what I plan is to put another open source firmware on it, namely DD-WRT.
The problem is DD-WRT is not supported for...
This 2821 router has been shut down for a couple of months and I'm trying to get back into it. I'm plugged into the console port and after it boots it comes to the message below. I hit return ...
Hi Experts,
I am learning some network security/cryptography materials and wanted to experiment with
capturing packets coming to/from my linksys(WRT54GS) router. I have two computers conn...
Hi there.
At home, II have been using dlink dir 655 wireless router for about 10 months. I now have to connect to my work computer (have not needed to do so before) through remote desktop af...
Hi,
We have a Cisco 2851 router and I have a local install of SDM (Security Device Manager) version 2.5 on my PC. I can run and access nearly everything in the SDM GUI but when i click on t...
I have a netopia R9100 Router...
I can access it via telnet and have the password...but I want to change the password.
I find a setting called security and enter the user name and password...
I have 2 Cisco Routers and a Catalyst 2900 switch and I want practice with them. They were given to me and I have a cable to connect the serial end to my laptop and then the other end to an et...
I've been using my new Netgear DGN2000 wireless modem/router for a couple of weeks now and have attempted to setup Address Reservation on the LAN web page. I have a number of devices that con...
I'm on Optimum Online with a Motorola sbv5222 cable modem. Everything's been worknig fine, but I'm trying to set this up to work with a Linksys WRT54GS. When I plug the cable modem into the ...
I am trying to setup Route maps so I can send web/ftp traffic out one interface and all other traffic out the other. A bonus answer would also allow the second connection to serve up the web/f...
What I'm attempting to do seems relatively easy but it's not working right. I'm used to setting up a cable modem with a router but not so comfortable doing this with dsl. The dsl on the DG83...
I just bought this new wireless router Netgear WNDR3700 and installed it and everything seems to be working, however, when I pluged my external media drive to the network I can't see it my des...
I have a cisco 3550 catalyst switch that I would like to upgrade the IOS on.
The problem is that the flash directory contains a folder with the IOS image as well as an html folder. The html f...
I have a network of about 20+ computers with the need to block port 80 traffic on about 5 of them. The 5 computers have static IP addresses in the 192.168.0.x subnet. I have attempted to cre...
I have configured the the vlan on the cisco 2960 switch to be vlan 5 and created a vlan on the router to vlan 5, I have put all of the relevant ports into the vlan 5.
i have created trunk b...
I use a Netgear DG834GT ADSL router at home to connect to the internet.
The most recent firmware update, 1.02.19 introduced VPN support for up to 5 clients ( see http://kb.netgear.com/app/a...
The following instructions were set on the router
clock timezone GMT -4
ntp server 129.6.15.28
But the sh ntp status saids that the clock is unsynchronized.
CORE1#sh ntp assoc
...
I really need help with this one. I came into work and no one could get on the internet. I plugged into the router and it was in ROMMON mode. I checked the CF card, replaced it, reloaded the I...
Hi chaps,
Does anyone know how I can disable NAT and firewalling completely on a Thomson TG585v7 ? I want to use them only as ADSL modems to connect to the adsl line. The thomsons (we have ...
I have 2 routes to a specific destination address and would like to enable object tracking such that when one of the routes is down it will immediately failover to the second route. I realized...
