Ok guys here is what I am trying to do. Our network right now is simple we have 2 offices and each office has their own ISP. There is an RV042 Linksys router at each office in "gateway" mode a...
I am using a 2811 with a NM-16A. I am just getting it configured. The first line goes to a ACE console port and the second line goes to a 2960 for test. I can connect to the ACE and the 0 ligh...
Hi,
I have two CISCO 1841 Routers. One of them is configured with Lease Line and another one with DSL line. The DSL line configured Router using the same LAN as the Lease Line Router. Both th...
Currently on Shoretel Build 8.1 and we have 2 sites connected with IPsec tunnel, main site has 1841 and remote site has a 871 router. All the shoretel equipment is at main site. They have 2 ...
Hi Experts,
i want to save running configurations on cat ios catalyst 6509.
i have tried theses command
wr
copy runnig-config startup config
write terminal
but wh...
I have an issue attempting to use Policy-Based Routing on our Catalyst 3750G-12S running IOS 12.2(35) ipbase not enterprise. I have created the appropriate standard ACL and Policy-Map Statemen...
hi all i have two xbox plugged into my cisco and at the moment i can only get moderate nat on can someone help me out
my xbox config is below, we have two
Hi Experts,
We are using a Cisco 2800 Gateway which has 3 PRIs (2 long distance + 1 local) which is also connected to a Cisco Call Manager 4.2. Yesterday the primary went off line for a whi...
I have a dedicated connection from our cable company to be used for video conferencing, also a Cisco 1800 series router that would like to use for this... I have a public IP that I can use fo...
how do I configure crypto dynamic maps using cisco 3825 and a netscreen 5gt
Any easy way to copy the config from a Netscreen 25 to a netscreen 100?
hello Experts.
i have an issue where i can vpn into the office and browse one set of subnet (10.17.18.0) and not the other. (10.17.200.0). Internally i can traverse between the two subnets ...
I am setting up a helpdesk server on VLAN1 (172.16.1.102) and I need to be able to access the email server on VLAN 3 (172.16.10.102). So far I have not been able to make these two talk to eac...
HI
when i try to connect to a cisco aironet 1200 with a console cable i am getting a error access denied
I have reset the device to factory settings
How do i get into the device
If I get the CISCO871W-G-A-K9 with wireless and upgrade it with AIPS, do I need to add more memory?
Default flash memory is 20mb of onboard flash memory and a 4mb flash memory card accordin...
HI i got two 2800 cisco routers.I ordered for srst software on one router and cme on other router.How to verify which router has srst or cme.
thanks,
andy
In all my experiences using WCCP redirection (mostly with respect to WAN Optimization devices), I've always done the redirect to an internal device (behind the firewall). Can WCCP be run acros...
We have two Cisco 3560G switches and are running cat-5 between them using the gbic ports (using the plug in adapters). At night the gbic's have been going down, acting like nothing is plugged...
I have asked questions about this complex in the past, but now my questions are changing a bit.
Right now we have an apartment complex that has about 30 units that have the offering to get ...
We currently have an ASA5505 programmed as a static IP on a broadband connection. It is all configured with VPN's to various sites, etc.
We purchased a metro E-line from ATT and found tha...
I have a client who has a Bigpond Wireless (Mobile) internet service using a USB Sierra Card. She would like to also have wireless access, while at home, to a multifunction printer she has wh...
I configured a Cisco 871w router with the config below. DHCP is set up on a server attached to the router (10.10.1.5). Users of this router report they cannot connect through wireless, but w...
hi
I got phaser 8560 printer which is working very good but only problem is when user from vista try to give print and they go in print properties it get hang up and even it gives error ps...
I created a secondary by following the instructions on this link below. it works great but the two internal subnets are able to ping each other. I need to have two subnets and have a block so ...
I just bought a new Dir 655 Dlink router. When I used the program TCP viewer I see alot of advertisement and other things like Euroclick , akamaitechnologies, and other things going on in the...
