We have a two servers in an MS NLB configuration. I set them up as multicast (unicast caused too many issues) but we can not ping the cluster IP.
I read the following article...http://www.c...
I want to configure Netflow on a Cisco 3640 Router, as well as a few of my Cisco switches (2950's and 3550's) so they will send data to a server that I have a netflow analyzer installed on? ...
So right now my Juniper SSG 5 is setup so that ethernet 0/0 is the untrust, ethernet 0/1 is the DMZ and the remaining ports 0/2-0/6 are all considered trust (bggroup 0).
Please view attatch...
Could someone please help me with command to enable http (for web admin tool) on my cisco 800 router
I have tried following command but does not seem to work:
telnet to router (192.168.1.254...
I have a small network with 2 routers (wired and wireless). I recently added the wireless to provide connectivity for laptops.
Wireless Router is being used as a hub only. Internet access...
I am using a Cisco 1841 Router to bind2 T1 lines. I ma using the VWIC2-2MFT-T1/E1 controller card. it dosent seem that I can use Multilink to bond them...? so in the sample config of what I am...
I no longer have a laptop with a serial connection on the back that would allow me to connect serial to ethernet to the console port on the cisco router. My laptop now only has usb ports. Does...
Hello,
I'm having an issue trying to get one of the remote office's Cisco 877 to connect to the 2800 at the corporate office. When I run the show crypto isakmp sa command from the 877, the ...
hi,
i m trying to bind specific ip with mac address of client pc.so
client can not change their ip.i tried with ARP entries to make ip
static then make interface reply-only but if i did l...
Ok here is my problem
- ADSL/Router1 connected to the net and is 192.168.1.1, sub 255.255.255.0 (network1)
- ADSL/Router2 connected to the net and is 192.168.10.3 sub 255.255.255.0 (networ...
I'm implementing QOS on a cisco 2811 router with the following class-maps and policy-maps below. One of the issues I'm having is that its tagging the initial ftp handshake but when the downlo...
On my home network i have two routers, one broadband and one wireless router.
Broadband IP Address is 192.168.15.1
Wireless IP Address is 192.168.1.1
I would like to open a port through...
Hi,
I had a setup that was working fine as follows:
LAN -> PIX506 -> ADSL modem (Internet)
On the LAN side I had a SIP server with IP address 192.168.1.10 (static)
The PIX506 was configu...
Hi Experts,
I haven't configured CISCO routers in a while and this is my first attempt after a couple of years. I need to get it sorted very quickly for my customer so please help.
Its a ...
I have allowed a local loop back, hairpin?, for a device by using the following cisco commands:
hostname(config)# same-security-traffic permit inter-interface
hostname(config)# same-security...
Our network infrastructure is simple at most:
Lets pretend we have Router A (Running the latest Cisco IOS), which is directly connected to the "Internet" through the WAN port (for simplicit...
my old Linksys WRT54G Ver 1 went bad so I bought a new Ver 8. Now I need the settings. Here's my configuration (all Linksys): DSL modem to internet port on BFSR1. One ethernet port of BFS...
Hi there,
I want to confirm if URL filtering/IP Inspection am doing on Router 1 (a Cisco 2821 series router) is correct or wrong ?
Topology looks like this ...
Site A <----> IP WAN <---...
Here is my issue:
I have a PPPOE modem that receives internet just fine. To access the settings of the modem I go to 192.168.0.1. I would ilke to add a wireless router to the configuratio...
on GNS3 I am using 3640 routers as a router with NM-16ESW module to simulate a switch.
I started the router"Switch" telneted to the console.
I realized when I go to any interface and type Sw...
I administer a Cisco 2800 series router with IOS 124-22.T that I am having difficulty connecting via IPSec Tunnel to a Sonic Wall Pro3060 (Firmware: 4.0.0.2-51E) that I do not administer. Ph...
I have shorewall setup with the following zones (LAN,WAN, $FW) I have 2 internal dns servers for the network that forward to the internet via opendns. I want to force all network users to us...
Ok, here is my situation...I have been asked to set up an ACL that will allow one department to access the rest of our network (email, internet, etc) but will deny all incoming traffic that is...
Need the IPSU to setup the device
I am trying to configure a Cisco 878 with one of the 4 Ethernet ports providing NAT for an internal network and one providing a routed connection. I understand that this can be achieved using ...
