Hello trying to create a VPN connection between home (dd-wrt VPN) and work (cisco pix 501).
Will have DDNS at home with a Static IP address at work.
Never used the VPN stuff in DD-WRT a...
Hi all,
we have 3 internal address ranges
192.168.10.0/24 LAN
192.168.15.0/25 Wireless Lan clients are denied access to the lan from this range
192.168.2.0/24 ISA external interface
s...
I have a static route with a big mask (like 10.10.0.2 255.255.0.0 10.60.0.1)
Will a new network in the OSPF process with a smaller mask beat the static route? (like 10.10.2.0/24)..
Example
...
I have DSL backup on MPLS network. If there is a problem within MPLS Cloud (for instance routing issues) backup doesnt start. I implemented Object Tracking but it still doesnt work. Could so...
Hi
I've setup a Kiwi syslog server and configured a Cisco router to send messages to it but I'm not seeing any messages except for;
Sep 15 12:00:28.187: %SYS-5-CONFIG_I: Configured from ...
Hello,
First, let me describe our infrastructure. We have 10 servers and 100 clients. All clients are getting IP thru DHCP. Our LAN subnet is 192.168.x.x, 255.255.0.0. We have uncounted num...
I have just configured my router for the internet and it words fine. I am trying to configure port forwarding or nat t to 1 not sure which to use. I want to be able to remote in from home t...
I having problems few days, i have two routers & switch behind cable modem
It seemed no able to see each other, can someone give direction or point out the problems having
version 12.3
s...
We are getting ready to turn up our MPLS AT&T based network to replace our tired frame relay but I had one question before I do that. We are using the ATT managed service and I have been told...
Hello,
I have bonded two of my serial int. on cicso 1841 to combine the bandwidth. Routers on each end works fine. I noticed some of input errors and crc and number of interfaces resets. I...
I know how to configure wireless using sdm. I configured my cisco router so I can access the internet if my computers are directly connected to the router. I need to know how do I configure ...
I am trying to console into a HP 3500yl using putty. I have connected the serial cable and am attempting to connect. However the connection fails over all the port ranges i have tried. Does an...
I have a cisco 876 , which lost cookie value.
After a failed attempt to change coookie value i have to estimate the new password. The password is estimated as:
password := (i1+...+i5) mod ...
How do I configure Outbound Services on Netgear DG834GT Router ?
I basically have 2 home computers I want to allow access to the Internet between certain times, 1 pc I want to allow access ...
Have a wireless router computer that I have attempted to connect to the network with no success. When doing a ipconfig /all i show the IP address 169.X.X.X. Verified that the firmware is up...
Dear All,
We have been running a CISCO 1841 with 1x HWIC & 2 x FE for some time at our main offices. The router was confirgured with a static IP address on the WAN/dialer interface and a pr...
I have a Cisco 2600 router at the head end of my internet service. I have two T1-SCU/DSU installed in it, and two T1 circuits providing internet connectivity.
The two circuts (Serial0/0 and...
When Opening GNS3 Simulator, I can see on the Node Types panel , icons of PIX firewall and ethernet switch, but it doesn't specify which series they belong to.
I have IOS for ASA v7.24 and PI...
I have a Dell laptop (running Vista Home Basic) that I'd like to use as a second monitor for my desktop computer (running XP Pro). I did some Googling and found a program called Maxivista tha...
I am trying to upload the cisco SDM version 2.5 to my border router. It's a 2821 router. I have level 15 access on the device. When I launch the SDM setup program, it asks me to login to th...
I have a new Cisco 2811 series router, and I need to make sure the email flows through on the right IP both inbound and outbound to ensure that email will not be rejected by domains doing reve...
I am trying to gain administrative access to my router from a remote location. I was able to accomplish this, until yesterday. Yesterday, a BellSouth technician came out and replaced my DSL mo...
I am having trouble with an ACL on my cisco router. Seems straighforward enough, but simply doesn't work. Ive put my commands into the code view, please point out what i am doing wrong. After ...
Hi,
is there anybody who can explain what the number 539% on the ATM0/0/0 in bandwidth usage means ?
What does a 100% mean: your internetconnection is fully saturated ?
Thanks for helpin...
I have a laptop configured for internet connection sharing on a home network. It uses a PCMCIA card modem to connect to the web.
I now bought a D-Link Dir-615 Wireless router to un-wire mos...
