I have a laptop configured for internet connection sharing on a home network. It uses a PCMCIA card modem to connect to the web.
I now bought a D-Link Dir-615 Wireless router to un-wire mos...
Hello,
I need to change my Cisco router's gateway of last resort to 192.168.131.1..... I have no experience working with Cisco routers, but through some googling I was able to figure out w...
Greetings. I have two full T1 lines coming in with esf framing, and I need to bind them and use them as a single 3MB pipe to my remote site which also has two full T1 lines. I have a Cisco ...
Hi,
I have a wireless router which is a netgear WNR2000 and a couple of wireless devices which are having trouble connecting to the AP. All of the devices will connect at first however they w...
Hi,
First sorry for bad English...
We have purchased new Cisco asa 5510 firewall/router. I want to test and configure it. My network scheme:
internet<-->router cisco 2611<->LAN(172.30.1...
I have a static route with a big mask (like 10.10.0.2 255.255.0.0 10.60.0.1)
Will a new network in the OSPF process with a smaller mask beat the static route? (like 10.10.2.0/24)..
Example
...
I bring a new cisco 871 to my house and I subscribe to ADSL connection with PPPOA .
The router is in the default configuration .
I need to know what is the necessary command's to configure t...
GNS3 Devices.
I have an IOS for Cisco switch Catalyst 3750. I don't see this device on GNS3 console.
I would like to know if there is any way on how to download it and add it to the GNS3 c...
Hi,
I just bought a cisco router 857 and found out that it hasn't got any Ethernet Interface, as I've used some other 800 series routers which does have ethernet options.
It has fastEt...
Hi All,
some time ago i have been asked to forward port 52404 to 192.168.16.6 when coming from 210.54.x.x IP address.
i have done it by putting the following : (which works)
ip nat in...
I am getting Unknown Protocol Drops on my FastEthernet interface that I have configured for our Metro-e connection. Here is my sh int:
#sh int fastethernet0/1
FastEthernet0/1 is up, line p...
Just finished configuring my SSG5 for deployment. Rather than having to assign a static IP address to each workstation I want the SSG5 to be able to see a MAC address, then give it a IP. Rt ...
I have configured my 851 router as follows:
dot11 ssid Your-SSID
authentication open
authentication key-management wpa (needs to be taken out)
guest-mode
wpa-psk ascii 0 Your...
I recently discovered the 'ip sticky-arp' command in Cisco devices. However, I have a mesh network of Cisco/Foundry (Brocade) devices and do not know how to implement a similiar command for Fo...
Hi,
Where do we run Server Load balancing; I've a Cisco 2821 router, can I run the commands on that for SLB ? and do I need to install any additional module for configuring my router with SLB ?
Recently I did some work at a client's home to add a print server and a nas device for backup. His house was set up using a netgear wireless router in the attic of his 3 floor home. The dsl mo...
What command to I run from the command prompt to show the open ports on my Cisco 871w router.
I need to do this from the command prompt after I have telnet to the router.
Hi,
I have a Cisco877 device, that I would like to configure to route between 3 different networks. I don't necessarily need it to be connected to the internet for now, but I would like it to...
I have a client with a network with 7 or 8 PC's they are experiencing really slow internet speeds. The ISP came out and tested their connection and by plugging in his laptop got 3M download sp...
Hi guys,
I have one TrendNet router. Model- TEW432BRP. Now, it has not been working properly. Yesterday, I had problems with my network and my network was down. Today mornin...
Hi there
NLB is configured b/w 2 windows 2003 servers configured in unicast mode ... they are connected to a cisco 2960 switch ... periodic timeouts occur i guess due to flooding problem ... ...
Hi i have scenario where i need to send traffic out of an interface that is recieved on. i hsave not done this in a production environment yet as this is to be tested live with a customer netw...
I have setup faste0/0 to be link in from the ISP. and I have set up faste0/1 to be a corporate subnet (10.1.1.0).
I can ping the router from a machine on the corporate subnet. And I can pi...
Hello,
I recently started a new job working in the retail industry. One of the first things I've been asked to do is to replace the Cisco 871 router at one of the retail locations with a Cis...
Have connected an RVS4000 as Follows:
LAN IP: 192.168.10.1 Gateway Mode
SMask: 255.255.255.0 RIP v1 Enabled
Port 1 Connected to Novell Server on 192.168.10.25...
