i have moved houses and got myself a cable internet connection. i just configured my wireless router by going to 192.168.1.1 and set up WPA Pre-Shared Key security. the wireless connection is ...
Router on a stick config issue:
I have a switch with 2 vlans vlan 10 and vlan 20
3 routers are connected to the switch,first 2 routers are used to simlate PCs. and the third router is co...
Hello, I would like to enable SSH access to my cisco router from the outside. I would also like to allow access from only 1 IP address.
I have a Cisco 3560 sitting behind an ASA failover pair. I currently have a routed port on GE0/3 with an IP address of 192.168.110.20, I have my machine plugged into this port with an IP addr...
when I go to the connect to network, I don't see my wireless g 2.4ghz as a choice to select. I've enable the SSID and the wireless broadcasting options but still don't see it. Any idea why and...
I have a Cisco 2801 router that we have our internet connection running through. I am wondering if there is an easy way to find out who is using all of the bandwidth. I am currently monitoring...
how do I block skype and msn messenger on netgear DG834N.
I have admin access and trying to reduce staff messaging from skype and msn messenger.
We have static IP from our ISP, and ARP cache table on our router is showing over hundred internet addresses.
Many of these addresses are on same subnet as our public IP, and many others are...
My situation is that my D-link wireless router will not let me connect to web sites that are part of my account at Lypha. Additionally, I cannot receive email from those same domains. I have ...
We are setting up a Cisco 2801 router with multiple VWIC-2MFT-T1 cards. We are multiplexing 4 Data T1 lines.
in the config we of course have the following lines.
controller T1 0/1/0
c...
Dear all,
i've added two ACL and changed pwd of one users... after that i've restarted the router
after that i lost the whole configurations !!!
i've connected through console and it's ...
I am getting errors and trying to get a remote support user that is trying to help me with some website design.
I have him using QuickVPN I have created a user and password for him and he has...
I inherited a Cisco Router 3600 which was used for dialup RAS server. Of course, I do not have the password to the router. I booted into ROMMON and meant to enter "configreg 0x2142" but I ty...
I need help deleting the stuff off of the router and config it to work with my cable modem and wireless belkin 54g in my home
Experts,
I've been trying at this for a couple days, reading into a ton of possible solutions, but I'm not able to get a remote access VPN working with my Cisco router (1841)
I have succ...
Hello,
I have several networking devices in a subnet. One of those devices is a Catalyst WS-C4948 that had some VLANs and RIP(IP 192.168.100.105).
Rip conf:
router rip
version 2
...
We just installed two 6509-V-E core switches and we tried to setup VSS so both switches are one single virtual switch.
We then tried to bundle the access switch uplinks to the core into et...
I'm new to router configurations and am trying to resolve some issues with the configuration of an 1841 router. The router is currently configured with a multilink ppp with two T1s. We have a ...
I'm trying to help my friend setup his new DSL line with two routers. I am well accustomed to setting up a single router with cable modems, but this DSL modem has a router built in, and I'm s...
My company is finally going to start to switch from static IPs (on over 300 user PCs) to DHCP. I've started configuring DHCP snooping on my 3560s and 3750s, however I can't seem to figure out ...
Hi experts,
I've got a ADSL router-modem (draytek vigor 2820) that connects my network to the internet. DHCP is enabled, range 192.168.1.2-100 . Because the router has no wireless functiona...
This question has been asked before, but the answer was not a solution. We have a new Sonicwall TZ150 wireless that will not route wireless to lan and reverse also. I have tried building rou...
Help! I am getting this error and restarts from a Cisco 857 Router:
Code checksum failed--corrupted system image!
%Software-forced reload
Preparing to dump core...
Code checksum fail...
Need to put a vpn device which will have its own dsl service. This will sit behind a firewall. This device will need to VPN out to another site to create a vpn tunnel to access an application....
I am trying to set up a Linksys WRT54G on an internal 192.168.1.x network. My Windows SBS 2003 box is acting as the DHCP server, and I'd also like the devices hanging off the WRT54G to use ip...
