Question

Can't get tunnels up between DMVPN spokes Cisco 1841

Asked by: peter_sutton

Hi,

I have  a routerCisco 1841 that's attached to an ADSL modem so it's double natted its connecting fine to the mail DMVPN hubs but isnt picking up tunnels to other DMVPN spoke sites.

heres the config.. all help appreciated
Current configuration : 9123 bytes
!
! Last configuration change at 14:47:52 UTC Tue Oct 2 2007
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ank1-n-1841
!
boot-start-marker
boot system flash:c1841-advsecurityk9-mz.124-16a.bin
boot-end-marker
!

!
no aaa new-model
ip cef
!
!
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.201.1 192.168.201.100
!
ip dhcp pool default
   network 192.168.201.0 255.255.255.0

   netbios-name-server 195.163.13.186
   default-router 192.168.201.1
   dns-server 192.168.201.8 195.163.13.186 192.168.168.8
!
!
no ip domain lookup
ip domain name xxxxxxxx
ip host trinity.xxxxxxx 157.208.235.25
!
!
crypto pki trustpoint MYCA
 enrollment mode ra
 enrollment url xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
 revocation-check crl none
!
!
crypto pki certificate chain MYCA
 certificate 139800110000000000BE
  308204FD 308203E5 A0030201 02020A13 98001100 00000000 BE300D06 092A8648
  86F70D01 01050500 303E3112 3010060A 09922689 93F22C64 01191602 64733116
  3014060A 09922689 93F22C64 01191606 6D617472 69783110 300E0603 55040313
  07747269 6E697479 301E170D 30373033 31363133 35393339 5A170D32 37303331
    quit
 certificate ca 398B5D96C713EFA84B355CB151E7CC50
  30820452 3082033A A0030201 02021039 8B5D96C7 13EFA84B 355CB151 E7CC5030
  0D06092A 864886F7 0D010105 0500303E 31123010 060A0992 268993F2 2C640119
  16026473 31163014 060A0992 268993F2 2C640119 16066D61 74726978 3110300E
  06035504 03130774 72696E69 7479301E 170D3035 30393230 32313235 32395A17
  0D333030 39323032 31333530 305A303E 31123010 060A0992 268993F2 2C640119
  16026473 31163014 060A0992 268993F2 2C640119 16066D61 74726978 3110300E
  06035504 03130774 72696E69 74793082 0122300D 06092A86 4886F70D 01010105
    35600CB8 C5648402 87A375B5 D363E6D4 48CB61BA A4EA
  quit
!
!
!
!
crypto isakmp policy 10
 encr 3des
crypto isakmp keepalive 10
!
!
crypto ipsec transform-set trans1 esp-3des esp-sha-hmac
 mode transport
!
crypto ipsec profile golderwan
 set transform-set trans1
!
!
!
!
interface Tunnel0
 bandwidth 2048
 ip address 172.16.9.14 255.255.240.0
 no ip redirects
 ip mtu 1400
 ip nhrp authentication tank
 ip nhrp map 172.16.11.1 157.208.238.1
 ip nhrp map multicast 157.208.238.1
 ip nhrp map 172.16.7.1 64.42.200.140
 ip nhrp map multicast 64.42.200.140
 ip nhrp network-id 100
 ip nhrp nhs 172.16.11.1
 ip nhrp nhs 172.16.7.1
 ip nhrp registration timeout 30
 ip nhrp cache non-authoritative
 ip tcp adjust-mss 1360
 tunnel source FastEthernet0/0
 tunnel mode gre multipoint
 tunnel key 100
 tunnel protection ipsec profile golderwan
!
interface FastEthernet0/0
 description ADSL 2Mbps/512Kbps
 ip address 192.168.2.2 255.255.255.0
 ip nat outside
 ip virtual-reassembly
 duplex auto
 speed auto
!
interface FastEthernet0/1
 description 192.168.201.0/24
 ip address 192.168.201.1 255.255.255.0
 ip nat inside
 ip virtual-reassembly
 ip tcp adjust-mss 1360
 duplex auto
 speed auto
!
router eigrp 1
 network 172.16.0.0 0.0.15.255
 network 192.168.201.0
 no auto-summary
 eigrp stub connected static
!
ip route 0.0.0.0 0.0.0.0 192.168.2.1
!
ip http server
no ip http secure-server
ip nat inside source list acl_nat interface FastEthernet0/0 overload
!
ip access-list extended acl_nat
 permit ip 192.168.201.0 0.0.0.255 any
!

!
!
control-plane
!
call admission limit 75


!
scheduler allocate 20000 1000
ntp clock-period 17178510
ntp update-calendar
ntp server 157.208.255.6
end

ank1-n-1841#

This Question has been solved and asker verified All Experts Exchange premium technology solutions are available to subscription members.

Subscribe now for full access to Experts Exchange and get

Instant Access to this Solution

  • Plus...
  • 30 Day FREE access, no risk, no obligation
  • Collaborate with the world's top tech experts
  • Unlimited access to our exclusive solution database
  • Never be left without tech help again

Subscribe Now

Asked On
2007-10-02 at 08:55:05ID22866725
Tags

dmvpn

,

cisco

,

nhrp

Topics

Network Routers

,

IPSec Security Protocol

,

TCP/IP

Participating Experts
3
Points
250
Comments
4

Trusted by hundreds of thousands everyday for fast, accurate and reliable tech support.

  • "The time we save is the biggest benefit of Experts Exchange to Warner Bros. What could take multiple guys 2 hours or more each to find is accessed in around 15 minutes on Experts Exchange." Mike Kapnisakis, Warner Bros.
  • "Our team likes having a resource that is more secure than just using Google and most experts using this service really know their stuff. It's nice to look here first versus using Google." Dayna Sellner, Lockheed Martin
  • "Anytime that I've been stumped with a problem, 9 out of 10 times Experts Exchange has either the accepted solution or an open discussion of the potential solution to the problem." Kenny Red, eBay Inc.

See what Experts Exchange can do for you.

Got a question?

We've got the answer.

Experts Exchange has been collecting answers to technology questions since 1996…3 million and counting! If you have a question, chances are we already have your answer.

Screenshot of Experts Exchange Knowledgebase

Need individual assistance?

Our experts are ready to help.

If you can't find the exact answer you're looking for, ask our exclusive community of 50,000 experts. You’ll get a personalized answer from a trusted professional.

Screenshot of Experts Exchange Knowledgebase

Want to learn from the best?

Read articles from industry experts.

Thousands of free tech tips, tricks, how-to’s and tutorials are available in our peer reviewed articles section. See for yourself how smart our experts are, no login required.

Screenshot of an Article

Working on a long term project?

Store your work and research.

Save solutions to your questions, answers you’ve discovered through searching plus helpful articles in your personal knowledgebase for easy future access.

Screenshot of Experts Exchange Knowledgebase

Access the answers to your technology questions today.

Subscribe Now

30-day free trial. Register in 60 seconds.

What Makes Experts Exchange Unique?

Members of the expert community talk about why the experience at Experts Exchange is different than what you will find anywhere else.

Trusted by the world's most respected brands.

image of each brand's logo

Faithfully serving IT professionals since 1996.

Experts Exchange Logo

Try it out and discover for yourself.

Subscribe Now

30-day free trial. Register in 60 seconds.

Related Solutions

  1. PIX 525 that is doing NAT, ACL's and IPSec tunnels
    If the client is terminating IPSec tunnels on the PIX. Will traffic still need to meet ACL criteria to be passed to the trusted side of the PIX? The reason that I am asking is because of the way they have their PIX configured. This is not a question about setting up an ...
  2. EIGRP over IPSEC Tunnel
    I'm having trouble getting EIGRP to propogate the proper routes over the IPSEC tunnel. Any help would be appreciated. I have three routers. Hub, Spoke-A and Spoke-B. Spoke-A and Spoke-B each have a ipsec tunnel to Hub. Spoke-A and Spoke-B do not have a direct connection t...
  3. IPSEC Tunnel on PIX 515E
    I have PIX 515E HA setup. I would like to setup IPSEC tunnel between my setup to customer end. Customer asked for following setup Tunnel customer end tunnal IP <--------------------> My end tunnel IP(my firewall outside Interface IP) ACL allow public IP(static NAT ...
  4. IPSEC VPN Tunnel and Static NAT problems
    IPSec VPN tunnel between HQ Office Cisco 1841 IOS C1841-advsecurityk9-mz.124-23.bin (IOS Image) 12.4(23) (IOS Version) (and the ) Branch Office Linksys RV082 The tunnel is working properly. Traffic is properly routing and protected. On the Cisco 1841 side, I ...
  5. ASA to 1812 IPSEC Tunnel
    I am trying to set up an IPSEC tunnel between a site with an ASA 5510 and another site that has a Cisco 1812. The configs are attached. what am I missing to make this work? I need traffic to flow unobstructed from the 192.168.75.x subnet to the 50.x subnet and vis versa. T...
  6. VPN Tunnels
    I have 3 sites that are connected by site to site vpn's using cisco appliances (asa or pix). One of the sites has had an IP change from the ISP. I need to ensure tunnels come back up. Should I only have to change the peer address on the other two pix's? Nothing else has c...

Free Tech Articles

  1. WARNING: 5 Reasons why you should NEVER fix a computer for free.
    It is in our nature to love the puzzle. We are obsessed. The lot of us. We love puzzles. We love the challenge. We thrive on finding the answer. We hate disarray. It bothers us deep in our soul. W...
  2. SCCM OSD Basic troubleshooting
    SCCM 2007 OSD is a fantastic way to deploy operating systems, however, like most things SCCM issues can sometimes be difficult to resolve due to the sheer volume of logs to sift through and the dispe...
  3. Migrate Small Business Server 2003 to Exchange 2010 and Windows 2008 R2
    This guide is intended to provide step by step instructions on how to migrate from Small Business Server 2003 to Windows 2008 R2 with Exchange 2010. For this migration to work you will need the fo...
  4. Create a Win7 Gadget
    This article shows you how to create a simple "Gadget" -- a sort of mini-application supported by Windows 7 and Vista. Gadgets can be dropped anywhere on the desktop to provide instant information, ...
  5. Outlook continually prompting for username and password
    There have been a lot of questions recently regarding Outlook prompting for a username and password whilst using Exchange 2007. There are a few reasons why this would happen and I will try to cover t...
  6. Backup Exchange 2010 Information Store using Windows Backup
    There seems to be quite a lot of confusion around the ability to backup Exchange 2010 using the built in Windows Backup feature. This stems from the omission of this feature prior to Exchange 2007 s...

Cloud Class Webinars

  1. Avoiding Bugs in Microsoft Access
    Alison Balter takes and in-depth look at avoiding bugs in Access. In this webinar you will learn about using the immediate window to debug your applications, invoking the debugger, using breakpoints to troubleshoot, stepping through code, setting the next statement to execute, ...
  2. Top 10 Best New Features in Visio 2010
    Scott Helmers gives live demonstrations of the top 10 new features in Visio 2010. This webinar will teach you how to create compelling diagrams by adding shapes to the page with a single click, linking the shapes in a diagram to data in Excel (or SQL Server, or SharePoint), ...
  3. IT Consultant Business Secrets Revealed
    Michael Munger, Experts Exchange tech pro and IT consultant, pulls back the curtain on his very successful businesses and answers question on every IT consultant and business owner should know about. He shares secrets on what he did to solve the 5 most common problems in IT, ...
  4. Disaster Recovery and Business Continuity
    Quest CTO, Mike Billon, gives an overview of the steps involved in building a dunamic disaster recovery plan. Through case studies and an examination of software/hardware tooles for monitoring and testing, you'll gain a better understandin of where you are, where you want ...
  5. Organize Your Visio Diagrams with Containers and Lists
    Scott Helmers uses cross functional flowcharts, wireframe diagrams, data graphic legends and seating charts to teach you: how to ustilize all three new structured diagram components in Visio 2010, the best practices for organizeing shapes in previous version of Visio, how to organize ...
  6. How to Us Objects, Properties, Events and Methods in Microsoft Access
    Alison Dalter gives an in-depbth look at objects, properties, events and methods in Microsoft Access. In this webinar you will learn about using the object browser, referring to objects, working with properties and methods, working with object variables, understanding the ...

Join the Community

Give a Little. Get a Lot.

Join the community of experts here and help other tech pros by answering question in your area of expertise. You can earn FREE access to all Experts Exchange's premium features and resources.

Join the Community

Answers

 

by: lrmoorePosted on 2007-10-02 at 14:16:32ID: 20002151

> it's double natted
>tunnel mode gre multipoint

GRE hates nat, even once, and I don't think that Multipoint GRE will ever work behind a nat device. I wish I had better news for you.

All of the Cisco examples for DMVPN show public IP addresses for the WAN facing interface. Yes, I know some show 172.16.x.x, but this is for example purposes only.

 

by: wingateslPosted on 2007-10-24 at 22:32:04ID: 20145274

The NAT is definitely the problem, you can get GRE(IPsec) out through NAT to a hub -actually you can NAT it a couple of times. The remote sites will never talk to each other properly. We thought we were close once... once

 

by: Douglas_FagerstromPosted on 2008-05-22 at 06:59:01ID: 21623852

is this question resolved?  I am facing a similar problem.

20120131-EE-VQP-002

3 Ways to Join

30-Day Free Trial

The Experts

98% positive feedback on 31,087 answers since March 2000. angeliii is a Microsoft Most Valuable Professional for his work with MS SQL Server & Develoment.

He has also proven his knowledge of Visual Basic Programming, PHP Scripting and Oracle Databases.

The Experts

97% positive feedback on 10,752 answers since July 2000. lrmoore has more than 18 years experience in the networking industry.

The six-time Mircosoft MVPs specialties include firewalls, virtual private networking, and network management.

Testimonials

"...and excellent source for support... Kind of like having your very own IT dept." Electriciansnet

Testimonials

"I was apprehensive at signing up at first. However... it has already made my life as an IT administrator much easier." JaCrews

Testimonials

"WOW! You guys have great, active, and knowledgeable people on here." moore50

Business Clients

Business Clients

In the Press

"If you’ve got a question... Experts Exchange can supply an answer.”

In the Press

"...an invaluable aid for both IT professionals and those who require tech support."

In the Press

"where IT professionals provide quick answers on just about any topic"

Business Account Plans

Loading Advertisement...