I currently have a Comcast Business IP Gateway, SMC8014, connected to a switch with multiple PCs. I want to add wireless so I want to add my own wireless router (using a Netgear WPN824). Thu...
I have a Cisco 1841 it says at boot time:
---
Readonly ROMMON initialized
PASSWORD RECOVERY FUNCTIONALITY IS DISABLED
---
Sending a break when the unit is powered on has no effect.
...
I keep getting ports on several Cisco 2950 switches that will go into ERR-DIS mode and not come out.
It seems to be random.
Each port is directly connected to a computer running Windows ...
I just purchased a Cisco 871 router off ebay and it came with a config on it with a console password. I check the internet but could not find any docmentation
I have a WRT54G router from LinkSys. Every now and then the router freezes and I have to reboot the router. Five seconds later I'm "in the air".
That's all fine, when I'm in the neighborhoo...
OK, who can make me understand the reason behind the loopback interface? As I understand it, there are at least two good reasons for a (virtual) loopback interface.
1. To test a router. ...
I am unable to access our Cisco 2811 router. It will not accept any userid/apssword combo. So I hooked up a console bale to it and telnetted in. Then I rebooted the cisco and hit "ESC" in h...
I have a cisco router with a public and private subnet on the Ethernet side of the device. we had to add some ACL's to help control some bandwidth problems but now for some reason all traffic...
I am looking for some sample IOS QOS configurations, particularly a real world example anyone might be using. In particular I am trying to apply QOS to Cisco VOIP and Citrix. I have followed...
I got a cisco switch to pratice with but router was configured before and I do not have username and passwordword. How can I reset this router to the default state?
I have asked this question before and noone replied. So here it goes again. I have like 25-30 switchs on my network; 2950s to be exact. I need to log into each switch and copy each config...
Hello,
Have a Cisco ASA 5520 appliance and i would like to configure it to use 2 ISP's for the purpose of load balancing. ISP A is a wireless internet connection with a range of IP addresse...
I have a wireless internet connection using the Belkin Wireless Router. I believe an unwanted person may also be using my wireless connection.
What security risks and implications does thi...
Hi,
I've purchased the cisco ASA 5505.
I want to configure the ASA with ASDM. The default IP address on the ASA is 192.168.1.1. I want to change it to the 192.168.0.0 range (for examp. 192....
Hi,
We are in the process of moving a very old T! infrastructure onto Time Warner's Metro Ethernet. I have gone through everything and just cannot seem to grasp the Trunking portion of my ...
Hi Experts,
Bit of a change of topic from my previous questions here. I have a D-Link 524 router, working well to share my broadband connection but I havent managed to get it setup for a pr...
Hi,
We have several VLAN configured in a Fortigate firewall and all of them connected to a DELL switch which supports VLAN. All of that is working properly. What we want to do now is to c...
The wifi side of my router failed after running fine for several months. I was sent a replacement router. The setup cd wizard worked fine for the wired side. I can directly connect from a c...
hi!
i'm trying to configure LINKSYS WAG200G model and was not successful configuring it.i used the setup wizard cd for the configuration. i know i may overlooked something.
is there any...
I purchased a used Cisco 2811. Now how do I force a reset on the device to return it to factory defaults? I have the console cable but can not telnet to the device.
Hi
I have 2 routers
Router1: Cisco 2501
Router2: Cisco 1750
I have connected both routers using serial ports ( HDLC ).
E0 port of Router1 is connected to a Win2k adv server ( 19...
how do i open a port or configure port forwarding if no router on network, Windows server 2003 is the router and provides dhcp addresses for all local PCs. I nedd to access a pc from outside b...
Hello!
Two basic parts that go hand in hand.
Unfortunately our CCNA training didn't cover running public services behind a router, etc. I am attempting to run a Web Server behind a Cisc...
Experts,
What is the difference between RJ45 and RJ48?
Are they both the same "Physical" shape and size?
Is this a standard which defines the pinout? If so, is EIA/TIA?
Does the numbering...
I am adding a webserver onto my comcast commericial network as I had in my previous non-commercial account. It seems the same options of mappping ports is not allowed. It was suggested that ...
