Hello,
We have a Catalyst 6506 with 2 MSFC modules in the same chassis. We have HSRP configured between the two for high availability. Recently during some packet sniffing, we noticed tha...
hello,
i currently have 802.11b. is there much of a difference between .11b and .11g? i understand .11g gives more of a range than .11b, but was wondering if it would improve router to wire...
How cna I clear a static route in a Cisco 2611 router. I have tried the ip routes clear * and the does not seem to work is there some thing that I;m missing?
I have fiber-optic to the house and CAT 5 from there to the network server (in my case a main desktop with a firewall router). I have an SMC 10/100 Mbps router at this point. I would like to...
I'd like to have from you a simple and short explanation on how NAT works and how to configure a good NAT on my router.
I don't want to search on the web because I would like to have a all in...
Hello, would it be possible to enable NAT only for a range of adresses?
Like for 192.168.0.1-192.168.0.49
so 192.168.0.50-192.168.0.254 will NOT have internet access.
Thanks in advance!
I'm using WinXP with Motorola SBG1000 Router. I 'm using edonkey p2p and i seem to be block from the firewall. I have set it to DHCP-enabled and i can't figure out what the lan ip is that i m...
Please see the diagram at http://my.core.com/~techmaster/net.pdf
I want to route packets destined for 4.2.2.2 on Network A over to the PIX firewall on Network B.
I have EGIRP running on...
I am using a CISCO 2600 Series Router,lately we sign up for an additional 2MBPS Leased Line,after I configure the Serial 0/1 link with an IP address and subnet mask,I get the message "Serial 0...
Configuration:
Cisco PIX Firewall Version 6.3(1)
Hardware: PIX-515E, 32 MB RAM, CPU Pentium II 433 MHz
PIX has 3 interfaces
Company has 2 internet connections.
They want the 1st i...
My Linksys BEFSR41 Switch/Router seems to become inaccessible and to drop Internet access occasionally, perhaps once per hour or so for a few minutes, a behaviour not exhibted with the same ho...
We have a cisco catalyst 2550 12g aggregator - it has the confiig for all of our vlans and functions as an integral piece of our multisite 200 user network. It is a single point of failure. ...
Are there any good books or web sites that are dedicated specifically to VLANs, or have significant chapters on how to properly configure them (preferrably with examples and/or step-by-step gu...
I am studying for the Cisco CCSP test and want to know how to configure IPSec with manual keys. I already have ike keys on the router and I don't know if the router can have both manual and i...
I have a Cisco 1760 running IOS 12.2 w/Firewall services connected to another PIX 506 Firewall for VPN.
The router has 3 cards: T-1, 100 MB Internal LAN, 10 MB LAN (used for DMZ).
I want...
I desperately need help please...
From the workstations on the lan with:
IP Addresses 10.1.x.x
Subnet Mask 255.255.0.0
we need to connect to BT router on tel no 01234 567890
they ...
I recently purchased a Cisco 806 Router in hope of implementing it into an office with 40+ users.
I want to setup a Bellsouth DSL modem in bridge mode and have the router do the authenticati...
Was wondering if anybody had a link to a pdf for this, or they can explain to me exactly what these options mean on my Cisco PIX 515E:
Pre-configure PIX Firewall now through interactive pro...
I have a cisco 2600 series router that I am attempting to use radius authentication. I would like to be able to log into the router using radius under normal circumstances. The radius server...
Hi,
My Scenario is
I have Cisco 3725 Router and 2* NM-16AM Modem Module in Network slot 1 and 2. I want to configure this dor Dial in. I am facing problem to configure this as Async inte...
On a netscreeen-5XP, can I set up port forwarding to accomplish what is below.
Please note, this is just an example, and I do not own nor use the static IP address below.
Example
66.151...
I have recently finished my CCNA accademy and am going to take the CCNA test. I am familiar with basic setup and design.
I have just purchased a cisco 3750 and need help with configuration/...
After putting it off for a while I'm trying again to get VPN working on a Cisco 1760 router, with no success.
My Current Config is as Follows:
Building configuration...
Current confi...
Hello:
I have a need to have an external router (Cisco 804) log into one of my
5350 NAS's. The 5350's are used for modem and ISDN dialup customers and
normally their authentication is ha...
I'm using several Cisco 3500XL Switches and each is programmed as follows:
Current configuration:
!
version 12.0
no service pad
service timestamps debug uptime
service timestamps log u...
