asked on

Cisco Catalyst 2948G Configuration

How can I configure a Cisco Catalyst 2948G running CatOS to have the following configuration:

1: Ports 1-24 have the network 10.7.4.0/255.255.255.0 with a gateway 10.7.4.1
2: Ports 25-48 have the network 172.24.0.0/255.255.255.0 with a gateway 172.24.0.1
3: both passwords are set to "cisco"
4: telnet into the switch is enabled
5: the configuration is saved so that it is there upon reboot
This is our first time using a cisco switch, and we are using it to setup a test environment (eBay purchase)

Thanks

PS: I know nothing of the CatOS so please type out the commands step by step. What happens when booted is in the code box below.

0:00.573688: Please set IPAddr variable
0:00.574267: Please set Netmask variable
0:00.574624: Please set Broadcast variable
0:00.574989: No gateway has been specified
0:00.575484: Network is not configured
WS-C2948G bootrom version 6.1(4), built on 2001.07.30 14:43:26
H/W Revisions:    Fin: 2    Head: 11    Board: 1
Supervisor MAC addresses: 00:09:44:4f:98:00 through 00:09:44:4f:9b:ff (1024 addr
esses)
Installed memory: 64 MB
Testing LEDs.... done!
The system will autoboot in 5 seconds.
Type control-C to prevent autobooting.
rommon 1 >
The system will now begin autobooting.
Autobooting image: "bootflash:cat4000.6-3-5.bin"
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC################################
Starting Off-line Diagnostics
Mapping in TempFs
Board type is WS-X2948
DiagBootMode value is "post"
Loading diagnostics...
 
Power-on-self-test for Module 1:  WS-X2948
Status: (. = Pass, F = Fail)
processor: .           cpu sdram: .           eprom: .
nvram: .               flash: .               enet console port: .
switch registers: .    switch sram: .
Module 1 Passed
 
Exiting Off-line Diagnostics
 
IP address for Catalyst not configured
DHCP/BOOTP will commence after the ports are online
Ports are coming online ...
 
 
Cisco Systems, Inc. Console
 
 
 
 
Enter password:
2009 May 26 15:04:01 %SYS-5-MOD_OK:Module 1 is online
2009 May 26 15:04:09 %SYS-5-MOD_OK:Module 2 is online

Open in new window

ASKER CERTIFIED SOLUTION

Don Johnston

membership

This solution is only available to members.

To access this solution, you must be a member of Experts Exchange.

Start Free Trial

2003domainadmin

ASKER

Could you please explain lines 2,3, and 6? Thanks

Don Johnston

Line 2 creates vlan 7 and places port 2/1 - 24 in vlan 7
Line 3 creates vlan 24 and places port 2/25 - 48 in vlan 24
Line 7 assigns an IP address of 10.7.4.2 to the switch and places it in vlan 7

2003domainadmin

ASKER

Set vlan 7 state active results in
VTP advertisements transmitting temporarily stopped,
and will resume after the command finishes.
Cannot add/modify VLANs on a VTP server without a domain name.

now what?

2003domainadmin

ASKER

I just ran clear config all, and show vlan. These are the results:
Console> (enable) clear config all
This command will clear all configuration in NVRAM.
This command will cause ifIndex to be reassigned on the next system startup.
Do you want to continue (y/n) [n]? y
......2009 May 26 16:40:24 %SECURITY-1-DOT1X_BACKEND_SERVER:No Radius servers co
nfigured
...
..........................................................

System configuration cleared.
Console> (enable) 2009 May 26 16:40:45 %PAGP-5-PORTTOSTP:Port 2/1 joined bridge
port 2/1

Console> (enable) show vlan
VLAN Name Status IfIndex Mod/Ports, Vlans
---- -------------------------------- --------- ------- ------------------------

1 default active 64 2/1-50
1002 fddi-default active 65
1003 token-ring-default active 68
1004 fddinet-default active 66
1005 trnet-default active 67

VLAN Type SAID MTU Parent RingNo BrdgNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ ------ ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 trcrf 101003 1500 - - - - - 0 0
1004 fdnet 101004 1500 - - - - - 0 0
1005 trbrf 101005 1500 - - - ibm - 0 0

VLAN Inst DynCreated RSPAN
---- ---- ---------- --------
1 - static disabled
1002 - static disabled
1003 - static disabled
1004 - static disabled
1005 - static disabled

VLAN AREHops STEHops Backup CRF 1q VLAN
---- ------- ------- ---------- -------
1003 7 7 off
Console> (enable)

Don Johnston

set vtp domain <name>

2003domainadmin

ASKER

Ok. now I have my laptop 10.7.4.3 and a san server 10.7.4.4 on the switch on vlan 1 but nothing is happening. it can't connect to the web interface on the san. The san has another ethernet port on another network and that network can see the interface. I can ping it though

2003domainadmin

ASKER

Correction: That works. but the second vlan does not work. It is on our actual network the 172.24.0.0 network.

2003domainadmin

ASKER

When I switch the SANs primary ehternet (172.24.0.230) to the switch and then connect the switch to our network via 25-48 ports nothing works

Don Johnston

Do you have a router that is routing traffic between the two networks?
Can the devices on each network ping it's default gateway?

2003domainadmin

ASKER

Oh How do I find the port mac address for port 48? It needs to be registered with our network

2003domainadmin

ASKER

Also how do I make sure that only 172.24.0.0 addresses work on vlan 24 and 10.7.4.0 address work on vlan 7

Don Johnston

Why? There won't be an traffic sourced from that MAC.

2003domainadmin

ASKER

whatever port connects the 1172.24.0.0. vlan to the 172.24.0.0. existing network in our production environment has to have its mac address registered otherwise it gets blocked. only half the switch is for testing, the other 24 ports (25-48) are for routing traffic in my office area.

2003domainadmin

ASKER

Thanks. I got everything working.