The choice available are
'WPA-Personal' - TKP or
'WPA2-Personal'- AES
which takes in a passphrase, but it needs to be converted into a 'WPA Shared Key' to supply for the client wireless d...
I have the following network setup:
Linksys 8 port router (RV082) at the center of my network. DHCP server turned on.
Two linksys wireless g routers (WRT54G and WRT54GS respectively) conne...
Heeeeeeelp :)
I have two Linksys gadgets...
One is a WRT54GC router - fine and small piece of hardware
Another one is an Linksys WAP54G Access Point.
I would like to connect these two ...
I have 3 computers in the household, 1 desktop and 2 Dell PCs
We have a wireless router (Belkin Wireless G Plus MIMO F5D9630-4)
The desktop is hardwired to the router and I can browse to...
I have four new Dell Laptops, two are Latitude D830's and two are Precision M6300's that all have this Dell wireless 1395 WLAN mini card. In the office we have wifi setup that all the rest of ...
I put a password on the above printserver, and now it does not respond to the router.
How can I reset or flush the password on this printserver, so it can respond back to the wireless route...
We just purchased a couple Cisco 1252 AP's to replace our old Linksys AP's that kept dropping wireless connections and poor performance. All we are wanting to do is install 2 of these AP's in...
Hello!
Probably a year ago I got brand new Cisco Aironet 1130AG (AIR-LAP1131AG-A-K9) along with ASA5505. I was able to set ASA for my small network, but I found that Aironet AP is not compa...
A friend has an HP Pavilion dv2035us. After connecting to my wireless for a few seconds we get that error message "Windows was unable to find a certificate to log you to the network" and it d...
We have an AT&T-supplied 2Wire modem/router as our primary router. It cannot be moved since it is located where the internet connection comes into our home and does not provide sufficient sign...
hi folks
as the question title said, i would like to convert my old WRT54G v1.1 (serial number beginning with "CDF3") from its Linksys firmware to DD-WRT based for better security control, ...
I have read all of the posts regarding similar issues with upgrading from LWAPP to Autonomous Mode. Here is my case:
I have 2x Aironet 1131AG Wireless Access Points.
One is brand new and...
Is it possible to change MAC address of access point (I have D Link DWL-900AP+, but I am also interested in general)? When I enter setup there is Advanced tab where there are some options tha...
How can I get a Linksys wireless router see an existing network?
I am doing a workgroup setup for a very small office (must be a workgroup cannot be a domain). They have a DSL business rout...
Hello experts:
I just set up a WAP (Netgear WG102) to act as a repeater. There is wireless access to part of the area but two of the furthest rooms get very low quality signal and it will ...
Using the Windows Wireless Client to manage WiFi connections and wanted to know if there was any way to determine the mac address of the currently associated access point? This is possible usi...
We have a small wired network based around a D-Link Modem/Router. In another building approx 20m away there is a Belkin Wireless Pre N Router set up as an access point wired back to the D-Link...
We purchased a new Cisco Aironet 1231G. I have worked with the 1200 series before but never this model. When I log into the console, I can get to enable mode but the unit does not take a "co...
I have two if these...one was NIB and it configured with no problems; the other was a "pull" from an office that was only up for a couple months. It worked flawlessly when first deployed. Now,...
hi, i have a dlink DWL-2100AP , suddenly the power led is blinking all the time and i can't locate its ip address. i tried to reset it but no luck still the same.
The power is unplugged then ...
I hope this is in the correct area, if not please feel free to move and please excuse my error.
I have a wireless network at a public library that is essentially it's own network (ie, subne...
Hi Guys i have a AP 1200 series cisco which is already configureed but i want to make it to factory defualt and configure it for as hidden SSID and with WEP key how can i do it please help
...
Hello guyz,
I am new here and I am happy that I found this great forum after some google.
Well I use desktop, my OS is WinXP Pro. Before I was using Cable Internet and it used to work fi...
I have an area where several, as many as 5 or 6, Access Point's are within 100 or so feet of each other, and I need all of them to work. They are each on a different connection (3 different ds...
Hi
I have a cisco AP (1242) with a corupt flash image.... I have tried to find a new image to TFTP to the AP (as its dead). When I use the following file I get this error.....
Base ether...
