I have a Cisco 1841 it says at boot time:
---
Readonly ROMMON initialized
PASSWORD RECOVERY FUNCTIONALITY IS DISABLED
---
Sending a break when the unit is powered on has no effect.
...
I am having a problem with my laptop connecting with my wireless router. It will only connect me to an access of "Local Only" and doesn't allow me to go on the Internet. I know it is my actu...
I have a new 2800 series router, and by default the username and password is cisco. Cisco says to change it with the following CLI command:
username <myuser> privilege 15 secret 0 <my pass>
...
I have a Cisco 1841 it says at boot time:
---
Readonly ROMMON initialized
PASSWORD RECOVERY FUNCTIONALITY IS DISABLED
---
I have reviewed much documentation in particular I have read...
I need a batch file to delete files and folders older than a week... I found out few from EE as well as other sites , but for some reason it doesnt work properly...
I've got a DB9 - RJ45 cable connected to my PC.
I've got hypterminal, and I've setup a new connection with 9600 baud, 8 data bits, 0 parity, and 1 stop bit.
I've tried with and without...
I just installed DD-WRT on my linksys WRT54G just so that my range can increase as when i use my iphone one floor below i get 3 to 4% signals...any advise on how to increase the throughput of ...
Hi,
We are in the process of moving a very old T! infrastructure onto Time Warner's Metro Ethernet. I have gone through everything and just cannot seem to grasp the Trunking portion of my ...
I have a USB Verizon Air Card and a LinkSys Wireless Router. What I am trying to do is connect another computer to this internet connection via the router. It can be either a hard or soft conn...
i am trying to do some things with packet tracer. I connect router(serial) to router(serial) and pinging works, but if i set router(fastEthernet) to router(serial) pinging packets lost. Probl...
I recently bought a new Wireless N Router. I followed the instructions on the CD's Step By Step guide but it still won't work, I only get to Step 3 and I get an Error stating "the internet ca...
Hi,
I need to rate limit apply a few rate limitng rules.
Firstly data going out via the private network cannot go over 2000000 bytes (2mb) and, anything going out on port 104 cannot exceed...
Is it possible to connect iPhone via VPN to SonicWall 2040 Enh OS?
I was given an HP LaserJet 4050N which seems to have a built in print server. The printer doesn't have a USB-port, my laptop doesn't have a parallel port. Can I connect to the printer through ...
I am trying to setup a Cisco 870 router to be able to do DHCP, NATing, and a VPN tunnel. Here is a copy of my config that I am using. I am able to get out to the internet on the router, butn...
Good Morning i just Bought a Cisco router 2600 I need to know a Link where i can learn more about it.
Setup Configuration. I am a new Cisco Student, I do not know much about them yet.
This o...
When configuring router only one line stays up, other line consistently goes down on protocol. Below is running config for Site 121 followed by Site 151 then interface status. While we do ha...
Hello
I have two cisco 837 routers and want to create communication between two servers that are connected to the routers
Server1 10.13.1.10 - connected to router1 10.13.1.1
Server2 192.1...
Hi,
Need to access Linksys router WRT54G [lost username and password, which I changed. Please advise.
Thanks,
Joe
I have 2 networks, a gre tunnel joining them. Our issue is pinging across the tunnel between networks. From telnet on router A or router B i can ping either router, tunnel endpoints, and any h...
Can anyone suggest a program that I can monitor all dsl traffic going through my router. I do not want to have to install a program on each computer.
Thanks
Hi
I have a problem. I have a net gear FVS114 and I cant reset the router because i need the network and how its laid out, i dont want to redo a DCHP in my clients envoriment and i cant be ...
I am trying to hook up a new Linksys WRT610N router to a pre-existing install of Verizon Fios that uses use an Actiontec Router. THe Actiontec has lousy wirelss coverage, but the wired part of...
Trying to establish a VPN tunnel between a Linksys WRV210 (public IP: a.a.a.a; private IP subnet: 192.168.150.0) and a Cisco PIX (public IP: b.b.b.b; private IP subnet: 192.168.1.0)
First ...
I'm preparing for CCNA and working in GNS3 simulator. I understand how to configure two routers now but having a hard time figuring out how to configure router 2 of this next configuration. ...
