I am having trouble connecting to my routers home page. I had a problem before and was advised to go to the home page (192.168.2.1) and utilise the 'use as access point' function. I tried this...
I formated my laptop and setup my wireless network card to realize that I don't remember the WEP codes anymore. So then I went to login into my router (NetGear FWAG114) and I can't remember t...
What is the default password for a 2Wire DSL router from SBC? Thanks.
I put in my password, and it won't accept it. I haven't changed it. What could have happened? HOw can I access it now that it won't accept my password? What can I do?
Here is the setup.
We have a DSL connection with 1 Static IP address and are using a Linksys RVS4000 VPN Router. The router is working great as far as DSL connectivity and we have been abl...
Everytime I access the Security area, it prompt me for the Level 15 access password. For Cisco device, the standard username and passworf is 'cisco' and 'Cisco'. How about the level 15 access?...
I get this message about 1 of 5 times from any site. Most often a retry will bring up the site on the second attempt but rarely, I cannot get to the site at that time. Sometimes the "Retry" bu...
We have a Cisco ASA 5510 that we are trying to set-up in a new envrionment. We used the management tool to "restore the device to a factory default config" however now the previous username /...
Hi, I'm currently using a NETGEAR Wireless Router Model MR314 and Wireless Adapter MA301. (802.11b) I'm not very well-versed in computers. I can't host Warcraft 3 games because of my router (w...
Hi again,
I have two Cisco switches, a 2950 and a 2900. I have been trying to configure them using tftp to update the IOS and text files to set up VLANs, Trunk ports etc.
I did the eras...
hi
how i can change password for
1- cisco switch
2- cisco router
3- pix firewall
thanks
I keep getting ports on several Cisco 2950 switches that will go into ERR-DIS mode and not come out.
It seems to be random.
Each port is directly connected to a computer running Windows ...
I need to enable port forwarding on 2wire router (2700HG-B), (port 80), but don't know the exact details.
I am installing Panasonic wireless remote monitoring camera. I need to register a p...
I'm having a hard time finding any information on whether the ASA 5510 and ASA 5520 support netflow?
I have a Cisco 1841 it says at boot time:
---
Readonly ROMMON initialized
PASSWORD RECOVERY FUNCTIONALITY IS DISABLED
---
Sending a break when the unit is powered on has no effect.
...
I have a client with a BIG house. There is network cable run to all points of the house (good news). But they also want to have wireless thru the house. I installed a routers and purchase two ...
I have a router CISCO 871 (4 fe ports and 1 wan port) and I want to configure new VLANs. I have this configuration in my router:
...
!
interface FastEthernet0
!
interface FastEthernet1
!...
I have a brand new NetScreen 5GT that I am trying to configure and am looking for help. I have never configured one of these before, though I know about other routers.
I am trying to accom...
Hi Experts,
Bit of a change of topic from my previous questions here. I have a D-Link 524 router, working well to share my broadband connection but I havent managed to get it setup for a pr...
I am having some trouble with policy based routing. I am trying to route any traffic that is from ip's 10.0.8.102 , 103, 122 and 123 on LAN Site 1 through serial 0 on r1
Any traffic from a...
I have a cisco 2924 switch and a cisco 3620 router.
Currently the switch has 2 VLANs set up on it because we had 2 separate networks before. Now we only have one network, and we need to ma...
I have a DLink DIR-635 Wifi Router and inside it has this option-
NAT Endpoint Filtering:
UDP Endpoint Filtering
- Endpoint Independent
- Address Restricted
- Port And Address Restricted
...
G'day,
I've been trying to reset my router, hitting that little button on the back but no success. Does anyone know if there's a procedure to pushing the button. I cant find anything on the i...
I need some new 3COM Visio stencils. Anyone know where I can find them?
I have connected my D-link Wireless N DIR-615 router to my D-link Ethernet DSL-320T ADSL 2+ Modem. I have done this my attaching an RJ45 ethernet cable in the 'ethernet' socket on the modem an...
