i could not find out why ATM protocol is used where ever DSL service is being provided? Why not TCP/IP protocol is used for these networks.
To me i think what ever Virtual circuits are doin...
Hi,
I have a cisco 1700 router with:
- 1 ethernet (fastethernet 0)
- 2 ADSL WIC (atm0, atm1, dialer 0, dialer 1)
- running IOS ADSL/IP/NAT : c1700-y7-mz.122-15.t2.bin
I am ...
I'm currently on a project where we are at a crossroad.
One of the companies that is involved in this project has indicated the need for an all ATM network from backbone to desktop.
I'm...
Hi,
I have a MPLS IP-VPN circuit DSL/ATM as following into code partition.
My service provider send an email to me that i must use the following modem:
Thomson TG605s for connecting to the ...
Hello All
I dont know if anyone can help but I would be grateful if you could. I have searched through the forum to find relevant answers but none seem to be related.
My problem. I live ...
I need help getting my virtual circuit to burst to full port-speed. We have configured a 20Mb/s sustained information rate (SIR) virtual circuit between two Cisco 7206 routers connected to a ...
Is there a solution to monitor/test the broadband speed at a preset interval ?
One of my client is having random problems on internet speed, at random time, users will complaint that their in...
I have been experiencing some issues recently at locations where we have routers with ADSL Interfaces as the primary interface. Basically it seems that the primary interface is up and does not...
I don't know if this belongs in the ATM catagory... but
My small business office (about 20 users) has been approached by a third party (www.itcdeltacom.com) regarding an integrated T1. Her...
hello ..
can any one explain for me what are the following :
vbr-nrt ? <-- ?
oam-pvc manage <-- ?
also whats the vbr-nrt rates fr the following speeds :
128k
256k
512k
768k
1024k...
We are looking at getting rid of our point to points and looking at MPLS. However, some of our locations are more rural and do not get MPLS, only MPLS lite. As from what I can tell, MPLS lite ...
I have submitted a request for leased line internet and i have been asked either Public ATM or Private ATM. My requirement is to have Public IP addresses at my end so that i can assign them t...
New Network, ATM Host is Up/Up on Cisco 3825 - Remotes all are T1(atm) lines using Cisco 2801 WIC-T1-CSU/DSU - all out of box new equipment
The host is up - trying to get 1st remote up - Al...
Hello all,
I have a client that has a point-to-point fiber connection between two cities. He wants to verify that he is getting the true speeds that he was told that he would get. Besides d...
I wonder if somenone can clearify
me if the standard implementation of an ADSL solution must use ATM as
the protocol between the ADSL NTU and the DSLAM?? As far as I read in
the ADSL Foru...
The issue that i'm having is that i'm trying to setup a VPN between two dsl customers but the two cannot ping each other. Basically i have the BVI setup with an ip address, lets say, "1.1.1.1...
Is it atm physical address is there like mac adress in case of ethernet. (when i'm using atm interface card instead of ehternet card in my pc ). I thought atm address means only Vc and VP...
I have a Cisco 1701 that has 2 x 1-ADSL WICs installed. I'm looking for an example configuration to connect this via our two ADSL lines and provide connectivity from the local FastEthernet0 in...
I am trying to wrap my head around some ATM calculations.
transfer burst <= 7 frames
1 frame = 2048 bytes of data
mean time between bursts = 80ms
bandwith required = 2.048 Mbps
calcul...
I have a cisco 7206 with M2t-t3 interface card and I have purchased a ds3 circuit with the following:
this first circuit is 3mpbs
VPI/VCI: 0 / 56
Terminate-from hostname: Hidden for secur...
See config below- the throughput is very low- how do I troubleshoot / correct this? what can lead to slow performance?
I did SHUTDOWN ATM1/0 but that didn't seem to help.
version 12.2
ser...
Hi Guys,
It's extreamly urgent situation. we got Zen internet on BT line and i want to configure it on a Cisco 1701 ADSL router. we got a blog of 8 IPaddresses, in which u all know only 6 are...
