HP ILO password change/reset

Hello,
I am running an HP DL380 G3 server and I don't have the HP ILO (integrated lights out) password.
Can someone tell me how to change this password, reset it to default or clear it out?  The ILO password tag was taken off the server and lost by my predecessor.

I have tried CPQLOCFG.EXE and HPONCFG.EXE and neither of these utilities seem to have a password change feature.

I have upgraded the ILO firmware to newest level (ver 1.82, 8/22/2005)

File: HPONCFG.EXE   Date: 10/28/2005
File: CPQLOCFG.EXE   Date: 10/6/2005

Thanks,
Stuart Helm, MCSE
I.S. Networking Lead
Awana Clubs International

FYI,
Syntax for the HPONCFG and CPQLOCFG commands:

J:\SHARES\HOME\StuartH\TEMP>cpqlocfg
CPQLOCFG v. 2.25 dated 10/06/2005
Usage
cpqlocfg -s [servername|ipaddress]|[:port] -l [logfilename] -f [input filename]
-v -c -u [username] -p [password]
Where:
        -s servername is the DNS name of target server.
        -s ipaddress is the IP Address of the target server.
           If a port is not specified, the port will default to :443.
                DO NOT USE this switch if launching from Insight Manager 7.

        -l logfilename is the name of the file to log all output to.
           A default file with the server name/ipaddress is created
           if this option is not specified.
                DO NOT USE this switch if launching from Insight Manager 7.

        -f input filename is the filename containing the RIB Commands

        -v Enables verbose message logging. By default, only errors and
           responses from GET commands will be logged without the -v switch.

        -c Will cause CPQLOCFG to check for correct xml formatting,
           but not open a connection to the management processor.

        -u username
        -p password  Command line user name and password override those
           which are in the script file.

J:\SHARES\HOME\StuartH\TEMP>
J:\SHARES\HOME\StuartH\TEMP>hponcfg
Firmware Revision = 1.82  Device type = iLO  Driver name = CpqCiDrv
HPONCFG RILOE-II/iLO setup and configuration utility
Version 1.3 (c) Hewlett-Packard Company, 2005

hponcfg [  /help  |  /?  |  /m firmwarelevel  | /reset [/m firmwarelevel]
          | /f filename [/l filename][/s namevaluepairs]
                        [/xmlverbose or /v][/m firmwarelevel]
          | /w filename [/m firmwarelevel]
          | /get_hostinfo [/m firmwarelevel]
          | /mouse [/dualcursor][/allusers]
          | /display [/allusers]

/help or /?           - Display this message.
/reset                - Reset the RILOE-II/iLO to factory default
/f filename           - Set/Get RILOE-II/iLO config from "filename"
/w filename           - Write the RILOE-II/iLO config to "filename"
/l filename           - Log replies to "filename"
/v or /xmlverbose     - Display all the responses from RILOE II/iLO
/s namevaluepairs     - Substitute variables present in input config file
                        with values specified in "namevaluepairs"
/get_hostinfo         - Get the Host Information.
/m                    - minimum firmware level.
/mouse                - Tune mouse and cursor parameters with speed tuned for
                        single cursor.
/mouse /dualcursor    - Tune mouse and cursor parameters with speed tuned for
                        dual cursor.
/mouse /allusers      - Tune mouse and cursor parameters for all accessible
                        users in the local Registry.
/mouse /dualcursor /allusers   - Tune all parameters with speed tuned for dual
                                 cursor for all accessible users in the local
                                 Registry.
/display              - Tune display parameters.
/display /allusers    - Tune display parameters for all accessible users in the
                        local registry.

J:\SHARES\HOME\StuartH\TEMP>
Start Free Trial