Can anyone tell me if there is a Delphi version of this routine out there to calculate the TCP checksum
/*
**************************************************************************
Funct...
I have a situation where my company has a site to site VPN with static addresses on both sides. The Vice President has just had an ASA device set up at his home and he has a Dynamic IP address...
I am using a Cisco ASA 5520 with three site-to-site VPN using ACL nonat and nat (inside) 0 access-list nonat. see below
access-list nonat extended permit ip 10.0.0.0 255.0.0.0 172.16.249.0 25...
I'm having trouble getting a Site-to-Site VPN stood up between a couple of ASA 5510's at remote locations. It doesn't look like the two ASA's are even attempting to bring up the tunnel - "sho...
When creating a IPSEC VPN can each side have the same internal network?
Location1 is configured for 192.168.100.x/255.255.255.192 which has the only server.
Both sides will have a Freedo...
Hi,
I have an urgent requirement to setup a temporary software VPN remotely between two sites, they were VPN linked between the gateways, but a hardware failure is now preventing this and I...
Hello Experts.
Would someone be so kind as to help solve my PIX 506E to PIX 515E IPSEC tunnel problem. I'm getting MM_NO_STATE on a site to site tunnel. Both PIX's have a dial in VPN (which...
I'm looking for a VPN solution for mobile users.
We've been using the built in Server 2k3 vpn, but have had problems with connectivity behind different routers, Linksys especially seems to ...
Hi. I've searched EE for this one and there are some similar ones but can't find step-by-steps to get this working. Situation is this:
SBS03 on 192.168.116.x - all working sweetly.
IPSEC...
I currently have an IPSec based VPN running between a Cisco ASA and a Cisco 2801. I'm moving my VPN connections off of the ASA over to a Cisco VPN concentrator 3005, which is in my DMZ. I'm ...
I connect to my office from my home via a hardware VPN. At the office, we have a Watchguard router and at my home, a Netgear DG834. However, the connection is very flakey - it drops and reco...
Hello
I put a visual html page in my website and fully explain the whole procedure of making a vpn connection for my users there .but always there are customers that encounter problem during...
New user inherited CISCO PIX525 I only know GUI
VPN set up 2 ways have 4- persistant connections (point to point - preshared keys)
VPN clients for sales people who connect from internet conn...
Configure a Cisco PIX 501 VPN connection with a Cisco VPN Client running and a Windows XP machine. And be able for the client to connect and get infor from the RADIUS server inside the network.
I have a unique situation where devices I have running Windows XP Embedded need to upgrade the firmware on a particular card. The card itself has two NICs, one internal, and one external. Th...
I need to set up a redundant connection between sites starting with 2 and eventually moving to 4.
The environment is using OSPF.
There are private T-1s between the sites currently. What ...
We run a VPN network and yesterday added a new store. We set the store up using PPTP and assigned an IP to the connection that would fit our local network (where the server is). I was able t...
I am trying to setup a site to site VPN with two PIX 501's.
The config as follows:
Site A - Static WAN IP 217.xx.xx.xx.xx, local IP 192.168.0.0 255.255.255.0
Site B - Dynamic WAN IP Local I...
Hello,
I was running Cisco VPN Client ver 4.6 on my PC at home and a laptop at work. I upgraded the work laptop to version 5 and tested it using a dial-out connection and everything worked g...
I installed a printer drivers on the terminal server so that one user could print from using using their home printer from the terminal server session. it is a dell photo printer i got the dri...
Does anyone know what happened to my favorite paid proxy service, Securenetics.com? It has been down for a while, and I can't seem to contact anyone in the WHOIS database. Any ideas? Any ideas...
I am
> new to Cisco and am having some problems. I am referring to this:
>
> http://www.experts-exchange.com/Security/Software_Firewalls/Q_22016322
> .html
>
>
>
>
>
> I am set...
I am using cisco VPN to open a tunnel. It is working over IPSEC.
What I want to do is once i use the CISCO vpn software it will use a different default gateway to access this network. Pl...
I'm not sure that this is even possible, but want to try and get some input.
I have a centeral site that runs Citrix servers and 12 remotes that connect to this site connected via IPSec tun...
hi
we are useing MPLS backbon running with BGP routing protocol now the chalange is to set encryption between sites how we can achive it i was trying with IPSEC tunnel but it is giving me MTU...
