August 29, 2008 06:01pm pdt

1. rpalmeira22 29,675
2. grblades 28,190
3. bfason 12,200
4. jdechiaro 10,850
5. Joel_Sisko 10,450
6. feptias 7,500
7. uetian1707 5,500
8. shepimport 4,100
9. lrmoore 4,000
9. KlBe 4,000
11. xuserx2... 3,600
12. daniel8193 3,500
13. cscocsco 2,950
14. harbor235 2,750
15. rlarian 2,350
16. noci 2,250
17. diepes 2,200
18. benhanson 2,000
18. CLoz 2,000
18. lecutis 2,000
18. MrHusy 2,000
18. tvman_od 2,000
18. cstosgale 2,000
18. aconaway1 2,000
18. bmasincup 2,000
18. mgob 2,000
18. FaithShield 2,000
18. decoleur 2,000
18. sirbounty 2,000
18. Mikal613 2,000
18. PeterMac 2,000
18. sunnycoder 2,000
18. bevhost 2,000
18. ehatchell 2,000

1. grblades 64,716
2. rpalmeira22 37,535
3. kode99 27,475
4. bfason 16,950
5. daniel8193 16,000
6. Joel_Sisko 14,500
7. feptias 12,600
8. jdechiaro 10,850
9. lrmoore 10,748
10. benhanson 7,664
11. uetian1707 7,500
12. leew 4,800
13. tvman_od 4,300
14. grant300 4,275
15. shepimport 4,100
16. cstosgale 4,000
16. KlBe 4,000
18. JRSCGI 3,628
19. xuserx2... 3,600
20. greekstones 3,500
21. cscocsco 2,950
22. The_R0CK 2,800
23. dkwiebe 2,750
23. harbor235 2,750
25. rlarian 2,350

02.26.2008 at 02:44PM PST, ID: 23195375

	[x] Attachment Details

point to point setup for VOIP and data using Cisco 2811 to Cisco 1721 setup

Asked by markdda in IP Telephony, Network Routers, Voice Over IP

Tags: Cisco, Router, 2800 Series, Setting up data/VOIP on a double Point to point circuit

Hello,

OK, here it goes..
We are installing an Avaya IP Office in our main building(Building A). We have an office in a building 500 feet away (Building B). We have installed a 2 point to point T1's between the buildings. Building B will get IP phones (18 IP Phones). Building A has a Cisco 2811 router with 2 WIC-T1's installed. Building B has a Cisco 1721 router with 2 WIC-T1's Installed. I would like one T1 to carry voice and one T1 to carry data between buildings A & B. My Voice network will be on a completely seperate physical newtork from my data network. What I need is help and advice on setting this up properly. The Voice network will be a 172.x.x.x and data will be 192.x.x.x. The network between the buildings will be 10.0.x.x and 10.1.x.x

Thanks in advance

markStart Free Trial

Keywords: point to point setup for VOIP and data u…

	Title
1	Need feeback for upcoming VOIP imple…
2	Avaya VOIP vs Cisco Voip
3	QOS for VOIP on cisco 3560 switch
4	What is the best VOIP Phone/Commun…
5	VoIP Config Question on Cisco 5400
6	VoIP On Cisco Routers

Loading Advertisement...

20080716-EE-VQP-32 / EE_QW_2_20070628

point to point setup for VOIP and data using Cisco 2811 to Cisco 1721 setup

Asked by markdda in IP Telephony, Network Routers, Voice Over IP

Tags: Cisco, Router, 2800 Series, Setting up data/VOIP on a double Point to point circuit

About this solution