I have an working Mitel 3300cxi 12-port POE Switch Appliance that has all 12 ports connected to Mitel 5235 & 5340 handsets. The users computers plug into a lan port on each handset. I have the...
How can I resolve a "Receive failure (Phase B)" error from RightFax 9.3 using a Brooktrout TR1034 family card?
I've checked my configuration against the support docs at captaris.com, but n...
How do I crimp a cat5 wire to a RJ11 plug
1. I have a private WAN that are (not connected to Internet) using MPLS to connect a few separate geographical location LAN. HQ LAN communicate with all sisters company LAN, but other LAN has ...
I have a 4506 switch configured and it's giving the followiing error messages
Nov 3 14:47:59: %C4K_EBM-4-HOSTFLAPPING: Host 02:01:91:46:66:01 in
vlan 901 is
Now I have bpdufilters on th...
I am having problems configuring Outook to dial out over our new Cisco VOIP system.
Cannot get the Cisco Lines to appear under the dialing options in Outlook.
Only the H323 and IPCONF lines...
We have just deployed Cisco call manager 6.1 and Exchange 2007 Unified Messaging. We are trying to get the fax function to work. I have read some postings in different forums that say this doe...
HI,
i need juniper global price list,
can anybody give a link or the document
thanks.
Hi,
I have installed a callmanager 6 server. I am looking for step-by-step configuration guide.
I have 10x7960 phones and a 7980 conferancing station. I got a 2811 that I want to use as gate...
Verizon wireless says that they do not need to give this driver. The card will not work without it. The laptop uses a Cardbus/Ricoh R/RL/5C476(II) controller. Does anybody understand the SSA c...
Anyone know of any good tutorials that I can use to study ATM. It would be best if they were downloadable PDFs.
Hi,
How do I create a loopback cable for my ISDN card? and
How do I run loopback tests?
When registering a new CTI Route Point in the Call Manager it does not want to register:
When running a query to see all CTI route points: "Find and List CTI Route Points" then all the rout...
Hello all:
We currently have a traditional PBX (inter-tel) and are looking for another alternative as our company grows. I have been looking at Asterisk and I am curious as to what I would...
We have a 3com SuperStack 3 NBX system in our office. For the past week and a half it has been dropping a lot more calls than normal. I have finaly narrowed it down to a problem with the D-Cha...
I've a 15 telephones network controlled by NEC IP2AP-6TXD main telephones
A company came and installed those telephones, then gave permissions using the main telephones
I tried to find infor...
The admin password is invalid for he telephone system. We need to make changes and can not access the internals.
Documentation refers to a password that does not work.
Is there a way to res...
How do I control which incoming numbers cause a given phone to ring?
We have Avaya phones, but the consultants that set it up are long gone. We just added a new employee and he has been se...
our office has 15 grandstream gxp2000 voip phones. My boss just bought the above mentioned switch, but i can not get POE to work. i followed the steps mentioned in a related post on EE with no...
I am working on setting up a VoIP solution for my company, and i have most of the details figured out and have a solid idea of what we want. I would like to go with the 2851 cisco Router and ...
I'm using cisco call manager. I have 1800 numbers that I have to temp pass off to other 1800 numbers. I set up a cti route point and it works fine. Here is the problem. These 1800 numbers ...
Hi,
I am trying to configure traffic shapping on a cisco 1841 router, which has 2 interfaces one facing the ISP equipment another one to our firewall. Our ISP informed us that they are polici...
Hello
i have a cisco 2821 isr and im trying to get the cme gui interface working. everytime i go to my routerip/ccme.html i get a blank page. could anyone help with this.
here is my runni...
Looking for advice and help on this one.
I've an alerting program that generates emails based on certain criteria (server down, service fails, CPU pegged, whatever else we wish). Now, I'd ...
I am trying to get the Iwatsu Programmers manual but everyone I talk to tells me it's some sort of special secret thing. I would really like to take a gander into this. I know it may be agai...
