Error Code: 0x643 trying to install netframeWork 1.1

The first one almost worked. It started the process but stopped before the error message. The second one i got as far as HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Updates........but did not see anything that looked like .NETFramework. Is there any other thing i can try? If not, do i need to have .netframework on my computer. If there is a way to get around it for the new ATI Drivers i would.....that is the main reason i was trying to install the netframework.....cause Ati is going away from the old control panel to the C.C.C. Which needs .NetFrameWork to work. Any suggestions?

Take Care, Lester Davis

Dear Experts,

I also got the error below when trying to install netframework 1.1......Is there AnyBody out there with Any Suggestions !!!!!!!!!!!!!!.

Thanks, Lester Davis



Microsoft .NET Framework 1.1 Setup


Error 1935.An error occurred during the installation of assembly 'System.Messaging,Version="1.0.5000.0",PublickeyToken="b03f5f7f11d50a3a",Culture="neutral",FileVersion="1.1.4322.573"'.Please refer to Help and Support for more information.HRESULT:0x8002802F.

One suggestion I've seen is to stop the Windows Installer service in services.msc, then try running Dotnetfx.exe.

It could be possible that a corrupt or partial previous install of .Net is getting in the way.
If you have a Windows XP CD, run setup.exe from the Support\Tools folder to install the Windows Support Tools.
Once installed, try running C:\Program Files\Support Tools\msicuu.exe.
See if Microsoft .NET framework is listed in there, and if so, select it and hit Remove.
When done, reboot, then try installing .NET again.

Do you NEED .NET? I wouldn't say you need it, but more and more programs are using it (like your ATI drivers). And no, there is no way to make something designed with .NET to work without it being installed. So, if you want the newer drivers, then yes you do need .NET installed.

I will try what you said in the post above. This problem i am having do you think that is why i can not check my hard disk for errors. When i try it says it can not open volume. I was just wondering if they are two in the same problem.

Take Care,

Lester Davis

What kind of message does chkdsk give you?
Is it "Chkdsk cannot run because the volume is in use by another
process.  Would you like to schedule this volume to be
checked the next time the system restarts? (Y/N)"
If so it just means Windows is using the volume, If you say yes it should check the drive and fix errors at the next reboot.

After reboot it says windows has finished checking disk and can not open volume for direct access. Takes about 2 seconds. It use to take a couple of hours to check  the hard disk for errors.

Hmm, yeah it sounds like something else is going on. Are there any errors in the system log in event viewer? Especially anything relating to disk?

These are my recent errors: I checked the Everest Ultimate Edition Event Log and this is what showed up------>

Event ID:32-Dependent Assembly Microsoft.VC80.MFCLOC could not be found and Last Error was The referenced assembly is not installed on your system.    
Event ID:59-Resolve Partial Assembly failed for Microsoft.VC80.MFCLOC.  Reference error message: The referenced assembly is not installed on your system.
Event ID:5007-TrueVector engine: File "C:\WINDOWS\Internet Logs\D2B5MM31.ldb" was corrupt and has been copied to "C:\WINDOWS\Internet Logs\xDB3.tmp".  File "C:\WINDOWS\Internet Logs\D2B5MM31.ldb" was corrupt and has been deleted.  
Event ID:7023-The Application Management service terminated with the following error:   The specified module could not be found.
Event ID:7001-The DHCP Client service depends on the NetBios over Tcpip service which failed to start because of the following error:   A device attached to the system is not functioning.  
Event ID:7026- The following boot-start or system-start driver(s) failed to load:   AFD  Fips  IPSec  MRxSmb  NetBIOS  NetBT  Processor  RasAcd  Rdbss  Tcpip  vsdatant  WS2IFSL  
Event ID:20-Installation Failure: Windows failed to install the following update with error 0x80070643: Microsoft .NET Framework 2.0: x86 (KB829019).  
Event ID:10005-Product: Microsoft .NET Framework 1.1 -- Internal Error 2908. {36C972E4-E1A5-4DFC-877E-8C291ECCA35F}  
Event ID:11935- Product: Microsoft .NET Framework 1.1 -- Error 1935.An error occurred during the installation of assembly 'System.Design,Version="1.0.5000.0",PublicKeyToken="b03f5f7f11d50a3a",Culture="neutral",FileVersion="1.1.4322.573"'. Please refer to Help and Support for more information. HRESULT: 0x8002802F. assembly interface: , function: CreateAssemblyNameObject, component: {608A2065-C580-4C1F-91ED-87286B7FDE1F}  
PDEngine:Unable to move file C:\Documents and Settings\Lester\My Documents\My Pictures\Pictures - Pro Digital Photos\ProDigitalPhotos CD 2-LD33709\ProDigitalPhotos CD 2-LD33709 026.tif after many attempts.  Skipping file.  
 


Any Ideas............................Also, I wonder if i can change my points for this question.......To me this is worth 1000 points now that i see it. If not maybe i can close it and start a new question worth more.

Take Care,

Lester Davis

At this point unfortunately I'm leaning towards trying "SFC /SCANNOW" from the command prompt, and if that doesn't help, backup data and do a clean fresh reinstall of XP. Depending on how much data and programs you'd have to backup and reinstall, it might end up taking less time to continuing trying to track this down. If you do post a pointer question to this one, maybe someone else will take a look and have some ideas.


What does this do? "SFC /SCANNOW". I started to reformat and do a clean install but hit the R for repair instead of clean install. I think i may just not wory about .netframework. But you have been very helpful and i have learned a good bit from you so i think i will take your advice and start a new question. But since you have helped me, not nessilty solve my problem but helping me understand a lot of things about my computer i think i will close this question out, award you the points and regroup see how my computer acts and start fresh with a new set of questions. Thanks so much for your help.

Take Care, Lester Davis