I am trying to configure QoS to prioritize outgoing and incoming traffic to a particular interface on my ASA 5510.
My outside connection is 6MB synchronous ethernet on Ethernet0/0
My loc...
I am trying to connect a remote firewall to the HQ ACS server. When I try to test the AAA server I recieve the message "Authentication test to host 10..X.X.X failed. Following error occurred -...
I have created a Site-to-Site VPN for 2 ASA firewalls and is able to ping both internal subnets with no problem.
However, on 1 print server 192.168.2.4 which is hosting a remote printer 172.1...
I'm having a problem allowing an RDP connection through to an inside host. Config is listed below. I'm static natting one of my outside static ip's (MAINSERVER-Outside) to an internal host I...
We have an ASA5510 that I need to block all web traffic except a proxy server and a few sites that do not work through proxy.
I was able to block all Internet access by only allowing the ...
How do I view a Cisco 515e log file without the use of a syslog server? What is the command used to tail the log file?
Hi all,
I'm trying to get this VPN going and I'm a little stuck...need a 2nd pair of eyes.
Note: I do not have access to the Concentrator config, Concentrator remote IP is labeled 20.20....
hello
i am having cisco asa 5510 firewall for vpn clients -
usually i need to give them key for vpn client configuration along with their user name and password but as i come to know - i ...
We have discovered a problem on our network where any large files we attempt to download gradually come to a halt. The cause of the problem appears to be our Cisco ASA.
We have a 50Mb pipe...
We are demoing an IPS and it noticed some traffic going to Port 137. I blocked it in all the ACL's for all the interfaces on my PIX 525. After I did that I started getting complaints about FTP...
I have the following network setup
DSL Modem from Time warner which provide me with Dynamic IP
To that I conected a Pix515 with inside (e1)Interface IP 192.168.90.4
To the Pix515 I have a C...
I am trying to get a L2L VPN top fire up on my two ASA 5505's
Result of >sh crypto isakmp sa
There are no isakmp sas
I have looked over my code 1000 times and cannot find anything.
...
Hi Experts,
I have configured both SSL and Cisco VPN access using ASDM wizard.
SSL VPN working very well and Cisco VPN Client connects but it's not allow even to ping to internal resourc...
I have been trying for a month to get a Point to Point VPN between a Cisco ASA5510 and Sonicwall TZ170 here is the info below.
Current devices:
Cisco ASA5510 in Location NF
Cisco ASA5510 ...
I'm currently having issues with SPAM originating from inside my office. I'm trying to rack down the machine that's causing the problems but it's been a slow process. One of the fixes I've rea...
Hi
I am trying to setup a l2L FW on a ASA ver 8 and getting the message on the show isakmp sa detail for phase one. trolling through the net indictaes it is the remote end who are using ...
I am currently using Solarwinds to monitor NetFlow traffic, however after removing the server to a offsite location I am having an issue externally logging into the Cisco with my SNMP credenti...
Hello all,
this Cisco ASA5505 is driving me crazy, everything with the IPSEC connection is working fine as clients can connect successfully with both phases, and both networks (inside and m...
I FINALLY got my ASA to properly authenticate against AD. The requirement was to allow split tunneling which I thought I enabled, but it doesn't seem to be working. I can connect no problem an...
I have two remote offices with ASA 5505 with VPN connections back to an ASA 5510 in my main office. I can ping both locations from the main office and remote office back to the main, but can ...
Hi Experts,
We currently use Cisco firewall Pix 515E. It's old I know. If we don't upgrade to ASA, is there anything, such as firmware, etc, we have to upgrade in order to still get the nece...
I have recently changed ISP and as such my external IP's have all changed. I believed that I had changed everything that was required but unfortunately it would seem that FTP does not work.
...
When using Cisco ASDM monitor I can only get graph output when the view is set to "Real Time-Data every 10 seconds". If I change the view to "Last 10 Minutes-data every 10 seconds", or any ot...
I currently have the SSLVPN CLIENT and WEBVPN configured to use radius. What I would like to do is create two AD groups one for the SSLVPN CLIENT users and one for WEBVPN users. The SSLVPN C...
We have a new ASA5505 with the Security Plus Unlimited License. We are trying to setup two web servers in our DMZ with PUBLIC IP addresses (as required by our application). These machines CA...
