The default class-map inspection_default on the asa has match default-inspection-traffic set as the match for the class. What does this actually match?
The current configuration for SSH on our Cisco ASA 5505 is:
ssh 0.0.0.0 0.0.0.0 outside
I'd like to remove this line from the config. What command do I use to do this? Thanks,
I have been tasked to modify the current PIX 506E firewall to allow a vendor to come in later this week who will establish a VPN connection to their server. This is a one day session only and...
We have a Cisco ASA 5505 and need to setup a site to site VPN with one our clients. We're going to setup a webserver for their intranet so that will be the only device in our encryption domain...
Hi,
1) I need to get clarification, confirmation and explanation (from the experts) related to Cisco VPN Configuration (Cisco ASA5500)
2)Would you pls explain the meaning and the goal of th...
Hi, PIX eperts.
We have just installed v8 of ios on pix 515e. Enable trafffic monitoring for top 10 source and destination. Its working but something very odd.. If I use my browser through ...
I have a Cisco Pix 515e running 6.3(4) I have 1 trusted interface and 2 untrusted interfaces.
Security level 100 for trusted
security level 10 for my second untrusted interface
security...
I have a Cisco 5510 router, how can I priorize my VPN traffic between two site (l2l) ?
Thanks,
I have tried to reset the password using Cisco's password reset procedure, however the Console port on the firewall is not responding to any commands. Even when restarting the firewall there ...
I have a Cisco ASA 5510 running a webvpn configuration. I have purchased some standard Entrust certificates, generated the CSR's, received the configured certificates, installed and tested.......
We are being required to add a second phyiscal firewall to our network to meet security requirements of a client of ours. Our current setup is 2 routers -> load balancer -> ASA 5510 with outsi...
Hello All,
I have a new modular CISCO 1841 router with 2 cards for aggregate bandwith of 1MBPS (512 + 512) and I need this router to simply act like an ADSL Modem to my PIX 506e firewall, j...
Dear experts,
i need to open the port 2525 on my firewall, for establishing communication between me and a third party company.
I googled it, and i've built a figure about it, but are ther...
I used to work with the Cisco Pix and have been away a few years now back needing to install a pair of redundant ASAs. With the Pix you just configured Pix A and then attached the cable and a...
So my company recently switched from a T1 line to a FiOS connection. We have been using a Cisco Pix 501 for a few years now with the T1 with no problem, but ever since we switched to FiOS, I h...
I'm trying to connect Location 1 and Location 2 together via 2 ASA 5505's. Location 1 and Location 2 both need to run on 192.168.0.0.
I'm having a hard time getting the 2 ASA's to create a...
Hi,
I am using cisco 1841 router. In the router log one message is diplay.
"*Oct 27 10:48:25.427: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on Fast
Ethernet0/1 (not half duplex), w...
Jut installed ASA 5510 and all is well except...
When users establish VPN connection, it requires username/password from the ASA LOCAl user database. How do I turn this off. I just want t...
I have a need to have a secondary subnet, like a DMZ, but not quite a DMZ. basically two seperate networks that route through the ASA.
Example:
interface 0/0: (internet IP subnet)
inter...
Hi,
Is there a command line entry that one can use to monitor smtp traffic in and out of the ASA firewall ?
I would like to monitor how many requests are made for our smart hots ip and i...
Hi,
1) I need to get clarification, confirmation and explanation (from the experts) related to Cisco VPN Configuration (Cisco ASA5500)
2) Would you please explain the meaning and the goal of...
Hi there,
network design is attached. The routers are connected to ISP's IP WAN that connects our colocation to all the routed sites. The PIX firewall is connected to the internet. Now we are...
I am adding a list of banned IPs & networks to some firewalls. These need to be banned incoming, basically to stop networks that have a high incidence of intrusion attempts.
Basically we ar...
I need to block inbound port 1935 in order to test RTMP rollover to port 80 - I don't know how to block specific inbound ports so that no one in my lan can use 1935 when connecting to servers...
Hi, I need to allow only https access from one particular vlan (VLAN10) to a particular server's (SERVER1) mgmt ip.
In the middle of the acl, an existing line allows access from VLAN10 to e...
