Hello everyone,
One of the orgranizations I work for recently hired a new executive director. He wants to be able to use the delegate feature in Microsoft Outlook. Because they are such a s...
I use a program called sawmill to parse our firewall logs. This is running on Server 2003 (32bit) with 4MB of RAM, plenty of hard drive space. The program used to work fine, and I could pars...
I have two questions regarding PIX static command.
1. On a PIX/ASA firewall, If the DMZ servers have public I.P, do we still need static commands for outside internet to be able to reach ...
Hi there,
I have 2 inside interfaces on PIX. Each of the interfaces are connected to 2 Routers (which in turn are connected into IP WAN where all the routed sites terminate). My question is t...
I have retired from service our main PIX 515, and replace it with an ASA 5540. Everything is working great, EXCEPT for some silly reason, the systems that I have on my DMZ are being blocked f...
I have a remote network that cannot pass traffic on my network while connected to my ASA 5505 via a cisco vpn client. I can see that the person has created a connection, but no traffic will pass.
Hi there,
Configuration of this PIX firewall is given below...You can see my public I.P address is 203.38.242.114/29 and ISP's gateway is 203.38.242.113. If I need to do port forwarding on my...
I am configuring a PIX 501 and I am able to send outbound traffic, send email, and access the Internet. But I am not able to receive inbound traffic, no incoming traffic to the smtp server, no...
replaced a sonic wall for a asa 5505 at one site (10.1.1.0, but now it cant VPN to 2 out of 3 sites. it connetced fine to 10.0.0.0 but not to 10.2.2.0 and 10.0.0.3 (im identifying the sites wi...
I have an ASA 5505 that will not route to the internet. I have a static IP range assigned by my ISP.
On the ASA I have the following route configured:
route outside 0.0.0.0 0.0.0.0 x.x...
Hello all,
I have a Cisco IPS 42xx series that is creating a new block for an ISP every 30 minutes, after it has expired. It is saying that it is caused by an ICMP hit, but doesn't really g...
I am coming into some really bad situations with an old admin that made some very poor decisions with the network and I am playing cleanup. they have a pix firewall 506E ver. 6.3, that has n...
I have been looking into the Threat Detection features of ASA V8.0(4).
From what I've been able to find out, if I enable Scanning Threat Detection I am likely to see a performance hit on th...
I am upgrading from an office store router to a Cisco ASA 5505. My office store router manages all port traffic including www, smtp, pop3, etc. and redirects some port traffic to specific IP ...
Hi.
We have two offices and recently connected them thru VPN with two Cisco ASA 5505. Now i' tring to set up remote clients to the main site but can't get them to reach the site-to-site.
...
Ok my ISP has had to reset there modem and my pix 501 almost everday along with them clearing there ARP. They have fixed my lines and replaced all connections. They say that I did not config...
I am playing around with Cisco ACL's and I am trying to understand how the ACL's are processed. If I want to block http I can use set up an ACE entry in the Inside_access_in ACL and that works...
I need some info on how to do this. I have a central location and two remotes. The central location has a Cisco ASA. It also has two T1s using a PowerLink for failover. The two remote locatins...
I have a Cisco Pix 501. I have it configured to run behind a small network which has a web server. I know ports 80 and 443 need to be open for the web server to function, but I was wondering...
I have a site to site tunnel with an external entity. I want to limit access to the kiev users.
I have created a kiev_limited policy and only granted access to one IP adddress. However ...
I'm making some internal IP changes to a few servers and need to alter a Cisco ASA 5505 to accommodate those changes, but I know very little about changing a Cisco firewall once it's in place....
I have a pix 501 that this morning I took out the following lines
access-list outside_in permit tcp any host 67.139.220.197 eq 3389
access-list outside_in permit tcp any host 67.139.220.196 ...
Hey Guys,
I have a pix 501 configured to use the vpn client. Everything works great except I lose the internet connection when I connect. I noticed that the default gateway that the pix is ...
The link below provides free ebooks to download:
http://www.ebooks-space.com/ebooks/CISCO.html
I believe it's legal, but if you try to open the downloade zip file, it asks for password. Ho...
I got the VPN's up in my previous question. Now I have a new issue. Namely, one of static NAT mapping. SHould be pretty simple. We are installing a new Cisco ASA 5510 to replace a Cisco P...
