Advertisement

06.29.2008 at 09:09PM PDT, ID: 23525865
[x]
Attachment Details
[x]
The Solution Rating System

With so many solutions, how can you tell which solutions are most likely to help you and which ones are not? To provide you with a tool to use, we rate our solutions based on various elements that most accurately determine if a solution is a quality solution. To explain what factors affect the solution rating, here are the elements we take into consideration when formulating our solution rating.

  • The Grade of the Solution
  • The Zone Rank of the Expert Providing the Solution
  • The Number of Author and Expert Comments
  • The Number of Experts Contributing
  • The Feedback of the Community

Your Input Matters
Because of the way the system is set up, the most important variable in this equation is you. As a member of Experts Exchange, you are able to cast your vote on the quality of the solutions in regard to how complete, accurate, helpful and easy to understand each solution is. When you provide your feedback, each rating is adjusted accordingly. So, if you see a solution that has a poor rating that you think is a good solution, let us know by rating it. As you do, the rating will be adjusted and will become more accurate for other members of our site.

If you have any suggestions that you would like to make for our rating system, please ask a question in the Suggestions Zone of Community Support.

Thank you!
9.0

Updating IOS on PIX 520

Asked by pcsonwheels in Cisco PIX Firewall

Tags: , ,

I just picked up a Csico PIX 520.  I am trying to copy pix631.bin to the memory and I am unable to do it.  If I type copy tftp://192.168.0.4/pix631.bin flash: I get this error:

Type help or '?' for a list of available commands.

From sho ver I get:
pixfirewall# sho ver

PIX Version 4.2(5)
Compiled on Tue 27-Jul-99 17:42 by pixbuild

pixfirewall up 4 hours 45 mins

Hardware:   SE440BX, 128 MB RAM, CPU Pentium II 349 MHz
Flash atmel @ base 0x300
0: ethernet0: address is 0050.8b63.b216, irq 11
1: ethernet1: address is 0090.2777.959e, irq 10
2: ethernet2: address is 0050.8b67.0319, irq 15
Serial Number:  18024129

From just tyrping ? at the # prompt I get

pixfirewall# ?
arp             Change or view the arp table, and set the arp timeout value
configure       Configure from terminal, floppy, or memory, clear configure
debug           Debug packets or ICMP tracings through the PIX Firewall.
disable         Exit from privileged mode
enable          Modify enable password
kill            Terminate a telnet session
pager           Control page length for pagination
passwd          Change Telnet console access password
ping            Test connectivity from specified interface to <ip>
quit            Disable, end configuration or logout
reload          Halt and reload system
session         Access an internal AccessPro router console
terminal        Set terminal line parameters
who             Show active administration sessions on PIX
write           Write config to net, flash, floppy, or terminal, or erase flash
pixfirewall#

It looks like some software is missing.  What needs to be done to get the new software to install?  It does have a floppy but no disk in it.

Thanks

Start Free Trial
 
Keywords: Updating IOS on PIX 520
Title
1 PIX
2 Pix to Pix VPN
3 PIX to PIX VPN issue
4 Cisco PIX and edge router, can't for…
5 Enable arp in ASA
6 pix VPN
 
Loading Advertisement...
 
[+][-]06.30.2008 at 12:06AM PDT, ID: 21897200

At Experts Exchange, members can ask their questions to thousands of technology professionals, also known as Experts. Experts compete and collaborate to answer those questions by leaving comments like this one.

Start your 7-day free trial to view this Expert Comment or ask the Experts your question.

 
[+][-]06.30.2008 at 09:29AM PDT, ID: 21900614

Often, when Experts are collaborating with members who have asked questions, they will request additional information about the problem. Askers respond with an author comment like this one.

Start your 7-day free trial to view this Author Comment or ask the Experts your question.

 
[+][-]06.30.2008 at 10:30AM PDT, ID: 21901184

View this solution now by starting your 7-day free trial. Setting up your free trial is quick, easy, and secure. We will return you to this solution, unlocked, when you're done.

 

About this solution

Zone: Cisco PIX Firewall
Tags: Cisco, PIX 520, 4.2.5
Sign Up Now!
Solution Provided By: raptorjb007
Participating Experts: 2
Solution Grade: A
 
 
[+][-]06.30.2008 at 10:31AM PDT, ID: 21901190

At Experts Exchange, members can ask their questions to thousands of technology professionals, also known as Experts. Experts compete and collaborate to answer those questions by leaving comments like this one.

Start your 7-day free trial to view this Expert Comment or ask the Experts your question.

 
 
Loading Advertisement...
20080716-EE-VQP-32 / EE_QW_2_20070628