Guys,
I came across a weird problem last week.
My ACL's for the match statements on the L2L VPN's have always contained the 'any' keyword in the source section.
eg. access-list VPN pe...
I have ASA 5510 and I am wondering if it is possible for me to use the management port like other ethernet port which can route all kinds of traffic. Please let me know. Thanks.
I was able to just copy and paste the 6.3 config into 7.0 and it worked fine for the most part. The commands that are giving me error are the following (pasting output below)
Is there anywa...
Hello,
Does anyone have any information on PIX IOS 7 release? I have all the info from Cisco about upgrade requirements etc but I can't seem to find any CLI references. I understand IOS 7 d...
I was having an issue with a PIX501 (4.2 Embedded Firmware) just hanging randomly after variable amounts of time under minimal load. I updated to the latest image available 6.3.5 and the lates...
How do I backup a cisco asa 5510 through the gui?
I'm authenticating to my ISP via PPPoE. Once authenticated I recieve the same public IP everything. I just setup a ASA 5501 today. Everything is working except I can't get port 3389 to port...
HI all, I am installing a Cisco PIX firewall and cannot get it to access the internet from the inside interface. This is causing me loss of connectivity as far as Exchange and Sharepoint serv...
Well here is the basic error that I'm getting:
08-26-2007 13:01:32 Local4.Critical 192.168.0.1 %PIX-2-106001: Inbound TCP connection denied from 71.63.71.***/3517 to 64.***.***.***/80 flags...
Our current pix-515-r-dmz-bun is no longer support (as of May). So at first I was just going to replace with the newer but similiar pix-515e-r-dmz-bun. But on a whim I called cisco presales ...
I have an internal Network of 172.16.1.0 on which all computers are assigned static IP's. There is a DSL broadxent Briteport modem on which I have the internal IP as 172.16.1.1 and that is the...
I can't get the cisco asa 5505 to allow computers to see the internet. The default config is supposed to allow this but I can't get it to. I've treid everything. Forget even trying to set up t...
Need advice on how to best setup outgoing access from a DMZ when restricting certain ports. By default I understand that the implicit rule is to allow all traffic to any less secure networks....
Group,
I upgraded my Pix from 6.3 to 8.0 and lost a couple lines of configuration, I realized there is a bit of learning curve between the different IOS so I needed help regaining the functio...
I'm tring to recreate this PIX command:
access_list nat0 permit 192.168.17.0 255.255.255.0
But it keeps saying this when I cut a paste it:
cda-pix(config)# nat (inside) 0 access-lis...
Hi,
If I have a WSUS Upsteam server on the LAN and have another WSUS server on the DMZ network beyond the firewall, what do I need to do on the firewall to permit the Upstream server to syn...
I currently have a web server in my DMZ and permit WWW to it from Outside_In ACL. Then the web server talks to back-end SQL server by way of DMZ_In ACL
access-list DMZ_In line 1 permit tcp...
IP's have been changed to protect the innocent!
I am having trouble accessing my FTP server in the DMZ. Does anything glaring show on the below config?
: Saved
: Written by enable_15 at ...
We have a client that has an ASA 5505 and I need to add a line (or lines) to the firewall config that forwards all incoming traffic directed at a specific port to a user's internal static IP a...
I trying to get a Pix 501 up and running, But traffic does not pass yet.
From the router it is connected to I can do an extended ping off of the interface the pix plugs into.
From the Pix PD...
I've searched around for the answer to this question, I may have found it but not have understood the answer. I've primarily worked with Linux based firewalls, with some PIX experience.
One ...
Scenario:
Our company just recently acquired a 9mbps internet connection for redundancy in case our main ISP connection fails.
Equipement involved:
We currently have a PIX 515 connect...
Dear all,
I am trying to upgrade my Cisco Pix to 7.0 but when i do it comes up with out of memory how can i clear the memory for the new os?
Lyon
Ok this is what is happening....
Office 1 - Branch office running IP adress 10.44.5.0 / 255.255.255.0
Office 2 Main office running IP address 10.44.0.0 /255.255.255.0
Office 1 + 2 are c...
I am trying to set up a cisco 877 for sweden with vpn, at the moment O cant get the natting working right, the router is online and ok and I can ping IP address and dns from there, however fro...
