Everything was working fine on the firewall until I ran the site-to-site wizard to connect a remote location. The remote location is 192.168.3.0 255.255.255.0 and the main location is 192.168....
I need to setup portforwarding on the pix to my internal 2003sbs server to use the Remoe Workplace option. I tried from the command line but , it's not working . Can you loo at my config and l...
OK - Got my Answer to http://www.experts-exchange.com/Hardware/Networking_Hardware/Firewalls/Q_22531345.html
Next Question is what about DMZ addresses? - Thet have a static tranlation too,...
Dears,
I plan to buy Authentication Authorization Accounting (AAA) system and I found the best two companies that can provide these services (AAA):
1- Cisco (ACS)
2- Juniper (SBR)
I wou...
I need to monitor bandwidth usage, so I have installed ntop on a pc that connect to the lan switch (unmanaged) right after pix firewall, but it reports only bandwidth usage for that pc and the...
I have a Cisco Pix 506E firewall with the configuration below, however the Exchange server cannot receive mail while behind the firewall.
The Exchange server has two NIC cards Local (192.16...
I am able to access the internet through my PIX 515E firewall but I am unable to ping anything outside eg. google.com????? I need to run a tacert route but cannot ping out ???? Why????? I do...
I have downloaded the 30 day trial of SmartFilter from www.securecomputing.com to see how it works. I installed it ok, or I thought. Then when it came time to view the data that it was collect...
I am trying to setup my cisco pix 515e to send email alerts to members of my helpdesk whenever there is an attempted intrusion.
I am a newbie to cisco , so any help would be greatly appreciated.
I am trying to implement some additional security features to protect our site from being blacklisted. The reason I want to do this is because a machine was infected with a virus and it sent ...
Hello,
I want to buy a Cisco Firewall for my web server but m not sure as to what and how is the user license and the RAM on the firewall will effect my server. And how many user lincenses ...
I have PIX with three interfaces. The outside interface is connected to a cable modem, the dmz interface is connected to network 192.168.1.0 and the inside interface is connected to network ...
hey everyone,
i want to setup my pix 501 firewall to the following
EXT ip 85.324.127.164
and internal ip 172.31.185.0/24
how can i do it? my ip address for pix is 172.31.181.14 i did...
Hi there
I'm doing a DR test for a customer
he has SMTP server on the inside of the network, which I've translated fine to
the problme is the DMZ, where his VPN server sits, it utilises p...
HI,
I published one FTP in IIS and it is working fine locally. If I try to access from out side, i am getting error " permission problem" I installed filezilla FTP client and I got the below...
I have a Cisco PIX 501C running 6.2 and the PDM. I would like to Upgrade to 6.3. I believe that this is non supported software and we do not have a maintenance contract. How can I purchase/...
Hi there.
I've been struggling with this for almost a day now and I've tried everything possible to get it to work.
Basically, my problem is as follows:
Using the VPN Wizard, I followed...
I have added my specific network and "0.0.0.0 0.0.0.0" but still get :
"unable to launch device manager from 66.249.107.100"
Related commands in config:
pdm location 10.10.1.109 255.255....
Hello,
We have a small development environment where we have multiple set ups of the same solution repeated.
In each solution is an Exchange server providing the mail functionatily and e...
We have a 506e and several remote sites that remote into the appliance. I'd like to run the VPN client on each site and leave the VPN client connected most of the time. Are there performance i...
I have an ASA 5505 with 2 WAN interfaces - 1st accepts and connects with the VPN client but the 2nd doesn't. I get the following messages in client log:
213 20:57:26.781 11/14/08 Sev...
Hi guys,
I have couple vlan, VPN, and LAN cisco network at my work and i'm just wondering there is any tool or software (GUI) to monitor these services ?
Hi,
How exactly do I add a global nat for all inside traffic but then also add in static nats for exchange / webserver etc.
I'm trying to fully understand the concept. I understand I nee...
Had a Cisco 501 pix firewall damaged by lightning strike. Cisco sent replacement. Can still hyper terminal into bad one. Need to send it back. What are the commands to put it back to facto...
The company I work for has recently purchased the assets, including the exising office space and IT infratructure, of a now bankrupt company. This included a already setup Exchange Server 2003...
