We have a CISCO 506e that has been setup for 3 years without changes. All remote users connect with this setup. Two users have begun experiencing problems about 6 months ago.
Have finally...
GOAL:
I have a web server in the DMZ (192.168.200.x) that the developer needs to RDP to from the main network (192.168.90.x).
FAILED "SOLUTION":
I have a route on my layer 3 switch to fun...
So during an update to my Cisco ASA 5505 I erased my flash - oops. I lost my images, so I can't boot my ASA. It boots directly to ROMMON mode. Is there a way to upload the file via a hyper ter...
I have configured a SSL VPN on a new ASA5505 and followed the cisco configuration example at http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008071c428.shtml
Of...
I using Cisco PIX in my HQ (PIX 515e) and many branch offices (PIX 506e) in a hub and spoke model.
I want the mobile client only need to connect to the HQ PIX using Cisco VPN client and fr...
We have 5 IPS from our cable provider, Charter.
Say x.x.110.249-253.
We want the first IP, x.x.110.249, to service basically all workstations in the network
IP 2, x.x.110,250, would be...
ATI-ASA-2(config-pmap-c)# no inspect esmtp
ERROR: Inspection not installed or parameters do not match
The above error is what I receive. I want to...
Each time I am using the Cisco PDM Version 3.0(4) with PIX Version 6.3(5) I find that I am connected initially, but when i try to apply any commands, I recieve the following error message : ...
I've tftp'd my asa803-k8.bin and asdm-611.bin to my Cisco ASA 5505. I get to the CLI prompt. What do I need to do now? I've asked this question before, and I tried to follow those steps but ap...
I can establish a VPN Tunnel from my Cisco VPN Client and I receive an IP address from the DHCP pool on the ASA however traffic will not pass down the tunnel, i.e. I cannot ping a server by ho...
Hi All,
Please help me....
I have just bought a Cisco 5520 ASA Firewall and now I need to setup a VPN to allow users to come into my network. I also need to set it up with two factor aut...
Hey all - We've implemented Exchange Activesync here and I'm looking to make the changes to our Cisco Pix 515 firewall found in Microsoft KB article - http://support.microsoft.com/default.aspx...
Hi Experts,
We are using the Cisco ASA 8.0 wwith ADSM 6.0.
We have created VPN users with remote access 2 issues once connected the user cannot ping a host by name only ip even though w...
I'm having problems with my ASA 5510 setup. I have setup three interfaces, one for the internet (outside), one for an admin network, and one for a curric network.
The problem is that I cant...
I would to have the my web server in he DMZ to have access to the Internet. I am hopinga pair of fresh eyes will help. I had this working then I broke it! Here's my config:
Result of th...
I have a working site to site VPN connection between a Cisco 5510 ASA and a Cisco 5505 ASA. The problem is the Cisco 5505 is on a DSL connection that is not a static IP, so when the IP addres...
I have a pix 501 and can log into it remotely using the PDM interface but not the serial interface. I need to do the reload command to restart the pix, but cannot get it to work in the comman...
After configuring some of my event sensor settings I got an error and could not get back into the IPS sensor using ASDM for configuration. Its been working great for months until now. After I ...
Hello,
This PIX was working ok last night, but this morning after I "reboot" it keep reboot in to a loop and show this error message:
mgsum_config: sumval(0xbd0d) md5(0x525ac23a 0x029b65...
Hi Experts,
I have a cisco asa 5520 trying to create an an object group acccess list.
JonesASA(config)#access-list inside_nat0_outbound permit object-group SpecializedReceivables object...
I have a Cisco ASA 5510 running version 8.0(3) of the ASA software and version 6.0(3) of ASDM. The ASA sits on the perimeter of our network connected to our DSL modem. The inside interface o...
When I enter in this static NAT command:
ASA(config)# static (DMZ,Outside) 106.66.51.27 192.168.10.27 netmask 255.255.255.255
I get this message:
INFO: Global address overlaps with NA...
I'm trying to get port forwarding to work for an 871W Cisco router for a web server and email. I've setup NAT and set rules in the access lists to allow traffic. Using the CLI to debug it (i...
Hi,
I have a little problem with NAT configuration.
Here is my network structure:
ISP ROUTER
|
|
ASA5505 EXT(A.B.130.130/30)
ASA5505 INT(A.B.244.0/24)
|
|
OTHER ROUTERS(Example: ...
I have a 3 interfaces setup inside, outside, and DMZ. This ASA uses a cable modem internet connection. The DMZ is for our open wireless internet connection, and the inside is for some of us ...
