Experts,
This is my first time configuring an ASA device, but not the first time I've configured firewalls. Although this device is new to me, the concepts are not.
I have a very simp...
I have successfully updated both the asa image and asdm to 8.0(4) and 6.1(5), respectively, on both an ASA 5505 and 5510 which I can access ASDM on both, but I have a third ADA 5505 here and I...
I need to create a static route from 192.168.13/24 to go to 192.168.0.210. Here is the scenario. I have two VLAN's. On vlan id1 the ip range is 192.168.0.0/24. On vlan id3 the ip range is...
We have an ASA 5510 firewall with no SSM and we want to block Skype using REGEX and Traffic Inspection. So far It hasn't been very successful because the fluid nature of SKYPE traffic. Cisco w...
I am configuring a Cisco ASA5505 with ASDM5.2. I have multiple routable public IP addresses. 67.x.x.194/27. I'm trying to route port 80 of one of these IP's to an internal IP (on the inside in...
I have a pix 501 and can log into it remotely using the PDM interface but not the serial interface. I need to do the reload command to restart the pix, but cannot get it to work in the comman...
After configuring some of my event sensor settings I got an error and could not get back into the IPS sensor using ASDM for configuration. Its been working great for months until now. After I ...
Hello,
I have a Pix Firewall With 2 Users that I need to change the Password then remove 2 users too. I am somewhat Familiar with routers but have never done this on a PIX..
username <us...
I'm trying to get a Cisco Aironet 1200 to show multiple visible SSID's. I have successfully created two, one of which is guest and connects users to VLAN 10 and is unauthenticated, the private...
I want to create a simple script that can be run daily against my Cisco ASA and Layer 3 switch to back up runnning congi. I want these backed up to a local tftp server. Maybe some thing that w...
I have been unable to run applications over a vpn connection since I installed an ASA 5505. I have tried adding the crypto isakmp nat-traversal 20 to the CLI but still am not able to run my ...
Does anyone know if its possible to add additional modules / equipment to Packet Tracer 5.0 ?
I am wanting to learn about the Cisco Pix and the Cisco 877 and they don't appear in the list t...
Hi!
Our webserver located on the DMZ needs to have a persistent TCP connection to a server located on the inside network.
This connection is a ODBC connection to our database. After 1-...
I am new to the world of Cisco networking. I've been a user of consumer grade products for a long time, and have a few 3Com switches and WAP's on my network, but we are needing to do more. So ...
Does anybody know of some sort of port testing utility which would include both a "client" and a "server" part, where the "client" part could allow me to test any port number for an IP address...
Just looking at tightening up security on a couple of ASAs we have, and we noticed that (as well as a user account we set up with privilege level 15 for ASA admin) there's one called "enable_1...
Hi Experts
Im new in networking side with some limited knowledge. I need expert's help to configure Cisco PIX Firewall. In code snippet i have the following configuration for PIX and look a...
I have been trying to get a tunnel up using policy NAT but have been unsuccessful. I have looked at the following thread:
http://www.experts-exchange.com/Security/Software_Firewalls/Enterp...
Hello,
I have a cisco asa5510 that I need to configure for vpn access by cisco clients
right now; and in the future l2tp connections for pcs without the client
software. I have tried to ...
Hi!
I´am stuck with a nat issue on my cisco asa 5520 device.
My configuration looks like this,
outside public_dmz
| |
| |
| ___ |
-|___|- Cisco ASA
| 10.1.1.1
|
...
I have recently setup a Cisco ASA 5520 but am unable to connect from the Inside interface to my DMZ interface. I have allowed icmp to any. Also I have turned off the firewall on my webserver o...
We are trying to setup an ASA 5520 to route traffic from our wireless network (192.168.10.0) to our data network (192.168.37.0). I get a reply when I ping the gateway for the data network (19...
(Sensitive information has been changed.)
I have the following two interfaces setup on an ASA 5520...
interface GigabitEthernet0/1
speed 1000
duplex full
nameif test
security-level...
I have working a VPN using Cisco PIX 501 running 6.3 code and a Cisco 3640 router. I'm have purchased a brand new ASA 5505 to connect to the Cisco 3640 and I can't even bring up the tunnel. ...
Hi all,
I just configured my logging server for my Cisco ASA (3CDaemon) And I need a good open source log analyzer. Can you recommend some ???
Thanks a lot for your support !
