Im trying to check my yahoo, hotmail, etc mails from my office. The Sysadmin has blocked everything which has anything to do with these domains on the proxy/firewall. I was wondering if there ...
Ok, we have a problem, need to setup a PPTP VPN between two locations. At our main office, we have a Cisco 3600 IAD provided by our T1 provider. We do not have control over this router. I can ...
Hello
My CISCO PDM does not work. I try https://internel_IP_Addr with IE6, but I get a "Page cannot be Displayed" Error.
The Basic Firewall hardware Configuration is as follows.
Gro...
I have two PIX-535's in a lab, configured for stateful failover. Upon initial configuration everything worked well. The active PIX was configured properly and it wrote the config to the stan...
Hello:
I am able to log into my network through a Checkpoint Secure Remote connection from home just fine. From there, I can ping, connect to servers using terminal services, etc. Everyth...
We are using Symantec Enterprise Firewall 6.5.2 for Windows NT/2000. We are using Lotus Notes R5 for email but I am trying to allow are client to send/receive email thru Outlook to and from th...
Hello, I am trying my first VPN connection to the office.
I can now log onto my internal domain as a domain user via my VPN but only if I use the Connectiod from the desktop and not from us...
I want to be able to access the web interface for my PIX firewall/router from any internal network address. What is the command line syntax for this?
I am trying to establish a Remote Desktop Connection to an XP Workstation through the internet using Microsoft VPN tunnel. The Sonic Wall is on my End and the following Ports have been opened:...
We are setting up a new install of a Windows 2003 VPN server through a PIX firewall. I can connect to the server fine from the inside, however from the outside I get Error 800's. The confusing...
Hi,
Daft question I guess but how do I delete a line from my Pix 515 config file?
I entertered this line
access-list inbound_acl permit tcp any host 217.154.240.59 eq ftp
but the ...
I have 5 lines for every second like this in the log:
19 11:10:55 3 IPG IPFIL FRAG Spoofed packet Fail 10.0.0.1>10.0.30.2 Prot=1 Int=eth0
The log is from a router with IP 10.0.01 - 10....
The challenge.
We have a group of ECG(echocardiogram) machines running an imbedded OS. They all communicate with a polling computer behind a pix 515E firewall. The polling machine(Abel), ...
Dear all,
I have a doubt on PIX firewall , while configuring for Dynamic NAT - ie to give range of IPs for the traffic going outside of my PIX, is there any parameter to calculate the numbe...
I have an exchange server that's being attacked I believe. The IP ranges are from 219.x.x.x to 222.x.x.x. How do I block these IPs in a Pix 506 firewall using version 6.2?
I am interested in maintaing my anonimity factor in various aspects of my computing ventures. I know little of firewalls. I plan on setting up a box with smoothwall software firewall. I wanted...
Hello,
I am looking for a firewall with the following features
- Totally invisible (Runs as a windows service)
- Blocks can be set by port number / domain / ip address / ip address rang...
I have URL Filtering enabled on my PIX 515 firewall for all traffic, but want to exclude an IP address. I have used what I think is the correct syntax as per the PIX help, but cannot seem to...
We are working with a PIX 515e, IOS version 6.3(3) with PDM v3.0(1). We have a limited number of IP's (about 4) authorized for PDM access. When you go to the screen within the PDM for settin...
I am trying to TFTP from my PIX 501 firewall at home over the internet to a TFTP server behind a PIX 515 firewall at my place of work, and it keeps timing out.
The messages on my SYSLOG ser...
Dear Experts,
I've just upgraded my PIX501 box with IOS 6.31.
It works, but my pdm complains now about a pdm software upgrade also !!! The actual version on my pix is 2.11, but not new eno...
Here goes...
At the moment, I have setup several site-site and client-site VPNs with the following simple setup:
Internet
|
PIX
|
Internal network
Everything is fine, hunky-dory. ...
Does the Checkpoint FW1 NG support inspection of RTSP traffic on port 554 to open RealAudio UDP ports like the Cisco PIX does?
If so, how is this configured?
Quoting from the Cisco docum...
using sbcglobal dsl then logging onto aol. all of a sudden it came up with this error wan miniport 678 error and I can't get onto the internet.. do I net the mini port? I only have 1 computer...
How can I reset the password so I can login to the web interface? I can login as admin from the command line. And, why can't you simply login to the web interface as admin, using the admin p...
