Hi All:
We have a pix that is connected to two internet providers. One security level 1 and one security level 2. The internet network is set at security level 100. We are testing the se...
I just installed a 515 and all is well. However, I'm having a difficult time getting thevpn working.
Here is my config:
and below the config are the logs from my vpn client.
thanks in ad...
Hi,
Having an issue with Juniper Network connect over ssl, all machines can connect with no problems, except one or two, when loading network connect they connect then recieve the error nc....
Hi Experts,
I have a new Cisco ASA 5520 with ADSM 6.0 i need to change an peer ip on a excisiting site to site tunnel.
I see that this is grayed out on the ADSM GUi that i would like to us...
Hello i have setup a VPN connection on a PIX 501 im able to connect to the host using cisco vpn client 4.6.
Im able to connect but i can not ping any hosts on the remote network.
But if ...
I am using a PIX 501 with VPN.
For most clients VPN works. However, for two of the clients, I receive the following error:
"Secure VPN Connection terminated locally by the Client. reason...
So here goes, I'm a Juniper newbie, but have to learn it because of a new job.
I have inherited a NS5GT, with it currently configured in port mode DMZ-DUAL-UNTRUST
Don't get me started o...
Hello experts,
My ISP/Administrator has blocked www.facebook.com!
I have tried using sites like bypassthat.com and other sites that use a web proxy service, but it said access denied too!
...
We're using Windows 20003 server RRAS for VPN, branch office routing and NAT. I have two NICs in the W2K3 server box -- the public NIC in the box is connected directly to the internet (no nat...
Hello.
I wanna configure a Windows 2000 PPTP client with GRE behind my PIX firewall to connect to the VPN Server outside.
The problem is when I try to connect the VPN server, my client g...
hi all
here's my problem i cant see the cisco pix demive manager after installing IE 7. screen stays at
loading pix manager please wait.
I am trying to setup MRTG which uses SNMP against targets. I need to setup our sonicwall firewall to allow SNMP and set the ip addresses and community for it. Does anyone know how to do this...
Hello,
I have a problem.
This message came up when a customer tryed to start a VPN connection, and I haven't any idea what I can do about it. Is there anyone who can help me!?
Message:
r...
Mar 02 10:42:19 192.168.2.250 %PIX-3-305006: regular translation creation failed for icmp src inside:10.1.1.9 dst phone:192.168.3.88 (type 8, code 0)
We receive this syslogerror when we ...
Hi all,
I'm new to the PIX\Cisco
We currently have all www and HTTPS traffic forwarded from the PIX to another device (ip - 172.16.17.2) and need it to be forwarded to a diffrent device ...
We have previously installed Juniper Netscreen 25 at one of our branches. We are in the midst of re-locating our data center, hence, we need to re-configure the NetScreen configurations. Unfor...
This has probably been asked before, but i can't access serach from here (no fault of EE) and looking for quick sol.
A friend has a broadband connection and is running McAffe antivirus (or ...
Hi,
I have a Watchguard Firebox II that one of the Junior IT guys here played with and rendered it usless.
Long and the short of it is the trusted interface is no longer responding.
I ha...
How can I setup Symantec Endpoint Protection Firewall to Allow incoming traffic on port 80 for a specific range of ips and block request for ips outside of the range specified?
I'm am trying to remove certain IPs from showing up in Websense reports. IPs like virus scanner updates and stuff like that. I don't need to see a list of 20 ips when I build a report for url ...
I am trying to setup site-to-site VPN between Checkpoint FW-1/VPN NG FP2 and Cisco 7120 Enterprise Router. The configuration is as follows.
FTP Client--->Cisco Router------>Checkpoint FW---...
Hello. Recently I have decided to purchase and add a Cisco ASA 5200 to our existing network which currently only exists of ISA 2k4 serving as both a firewall and web proxy. I am wanting to kee...
I recently had to re-install the Altiris Deployment Solution due to a hardware failure on one of our servers. We are running version 6.8 of the console. Everything has worked so far, but I a...
I am trying to configure a site-to-site vpn using my Checkpoint Express R55 VPN to another checkpoint VPN (version unknown) in the traditional mode. My encryption domain is currently defined ...
---from a router config--------------
crypto pki trustpoint TP-self-signed-265710673
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-265710673
revocation-check none
...
