I want to allow icmp between all the interfaces and to all the server connected to cisco asa firewall in different segment.
I'm working with a colo, so I have limited "access" into the network port itself. All I want to do, is set a SPAN port for a VLAN on a Cisco 2900, then have a Linux box monitor that port, and ...
Hi, i have routing problems with vlan1 secondary addresses.
The facts :
we have a 6513 and i want to set it as our company default gateway.
We actually have 4 subnets (10.72.128.0/24;156.0/...
We're looking for a software solution to monitor our servers and network performance.
Things we'd like to have monitored:
- Server RAM usage
- Available hard drive space
- CPU usage
- Ba...
I am using a .pac file to auto config our browsers to use our proxy sever (ISA 2006). This is just a bandaid type fix until we upgrade our routers. (Budget reasons). Using Group Policy, I have...
I have a new cisco catalyst 2950 series but i could not enter console mode i tried different console cable and it is really not working.. i tried to open other cisco router and switches and it...
I am working in c#.net (version 2.0) project. I need to create a polling service to talk to a device and get all its interface using get next.The inputs given are IP address of the device,the ...
We currently have a Ciscoworks LMS Server collecting all logging off of our Cisco Devices. Is it possible to have ciscoworks forward these messages to a syslog archive server? I'd rather not h...
is there a good solution that will allow company management to monitor LAN users internet activity in real-time?
I have a Cisco Catalyst 4507 Switch. Etherchannels are setup on the switch, but I am unsure if they are properly set. Is there any limitation to what interface can be on an Etherchannel? Do al...
Hi All,
Trying to configure VLAN trunk on Cisco switch.
IOS-based says:
Switch(config)# interface interface mod/port
Switch(config-if)# switchport mode trunk
Switch(config-if)# switch...
WhatsUP is an SNMP monitoring tool. MIBs don't load. WhatsUp recommends using an SMI compliance checker, such as http://www.muonics.com/tools/smicheck.php. This tool generates a long page of e...
I have created VLAN on HP 2650 Switch. Our default network is 172.50.200.0/21. The devices on this new VLAN will be manually assigned addresses in 172.50.192.0/21 space. The switch has 172.50....
Besides Cisco Route Manager 2.3, what other solutions are there to monitor and alert an administrator when route changes have occurred on Cisco routers? Archived reporting is also required.
...
Here is my situation. I have a computer that uses a cell modem to connect to the internet. Once connected to the internet we initialize a VPN connection. I also have a video recorder that c...
My client has a small network of appoximately 30 workstations. IP addresses are assigned by DHCP and have been for several years. The workstations are an assortment of Windows 2000 Pro, Wind...
Having a very annoying issue with Orion Network Performance Monitor. I've been on the phone with both Dell and Orion and this is where I'm at right now:
Created a custom MIB Poller using O...
Heres the config from a Cat Switch - theres a firewall plugged into FE01 - and the two vlans represent two DMZ's
The firewall is "multi homed" on the other end of FE01 and has an IP address i...
how do I copy the config from one cisco catalyst 3550 to another?
Our linux administrator changed the subnet of workstations
they are now 10.0.0.X
The servers and printers are at 10.0.1.X
I'm having a lot of problems with the 10.0.0.X workstations talki...
Hello again experts,
I have set up a windows server 2003 as DNS, with AD and as the domain controller. I have run both dcdiag and netdiag and all the tests pass. Whenever I type in the Doma...
I once asked a similar question but didnt get what i was looking for. I am looking for a software that will monitor the Wide Area Network devices (cisco routers) always and logs in a database ...
Looking for recommendations for what logging level to use on our Cisco equipment (i.e. 4- warning vs 7- debug) with an eye on Security. How much is too much, or not enough, when using a log c...
We have a domain with one Public IP (static). Many of the services are using ports on this IP. What are the benefits of using more than one public IP. i.e. running exchange, web services, term...
Ive got a Cisco 3750 switch with two Vlans; one that uses DHCP and the other one is for static addresses only. I am installing Cisco 1200 WAPs on the Vlan without DHCP but the clients connect...
