I have recently setup a Linksys WRV54G router. I have setup username and password for Quick VPN clients.
I have downloaded and installed the Quick VPN client on a Win 2000 Pro desktop. I ...
I have never setup a VPN connection using Auto IKE before and am having problems getting through Phase 2. The Error Message I am getting from the remote router is "Phase 2: No policy exists f...
Hi all
I'm trying to connect a Vista OS PC remotely to our VPN at the office. I am setting it up in Windows the same way as I did before in Windows XP. It connects on XP, 2000 Pro, etc., of c...
I have been running into problems with Cisco VPN client being install on DELL Latitude D530 laptops. I get an error in the middle of the installation " DNE Network install has encountered a pr...
I am trying to connect a laptop with a 802.11b wifi card to a corporate VPN using the Nortel Contivity VPN client. The local wifi AP is a Netgear WGR614 v1 router (i.e. it's 802.11b compliant)...
I installed the newest Cisco VPN Client (5.0.01.0600) on a PC with Vista.
if I want to connect to our Cisco VPN i get the Message:
Secure VPN Connection terminated by the Client.
Reason 412...
HI,
I have been trying to install the VPN client on my laptop. once i finish the instullation and try to access my VPN client software i get the following message
" the necessary VPN sub_sy...
Running an Windows XP SP2 machine attempting to install VPN Client 4.8. Didn't realize that it was already installed. After running the install again I am getting the folloing error message. "...
Scenario:
The office has a network with private IP:s ranging from 192.168.0.1 (the FVS318 router) to 192.168.0.255. The router has been set up for VPN according to instructions from Netgear d...
Hi,
I have openVPN installed and configured. When I run it, it gives me an IP with this log file (only a part is given here). I guess there is something wrong and openVPN doesn't actually w...
I was able to setup my VPN server with some help off of this board. I am using a Linksys Router WRT54G. Right now I can connect if I use the public IP address just fine, but when I switch to...
How do I create a Cisco vpn client .pcf file?
Hi,
my question is about the "local lan access" using the Cisco VPN client.
When I establish the VPN, all the traffic is injected in the IPSec VPN. Checking the VPN client status (Status...
I just downloaded Cisco's VPN Client version 5.0.01.0600 for Vista 32 bit. I was able to connect but the connection was immediately terminated by the peer and I got reason 435: Firewall Polic...
I recently installed Cisco VPN Client (tried versions 5.0.1.600 and 5.0.2.90) and when I disconnect a VPN connection the system shuts down with the error shown below. I am attaching a HijackT...
Where to start.. I'm just going to write everything.. More is better, right? I'm the type of person to read, read, read.. try, try, try until I hit a wall. Well, the wall is here in front of m...
I"m stuck at "acquiring ip address" in status window, my log says connection enabled, but I'm not connected.
I am trying to use HAMACHI VPN free version. However, it's been installed using a Hamachi IP from another system I have running on my network by mistake. It should have it's own Hamachi IP. ...
Hi,
I have a Cisco ASA 5505 which I have configured for VPN access and I can create a VPN connection fine.
The problem comes when I am VPN'ed in, I cannot access the internet/outlook ema...
I have been tasked to set up multiple site to site VPNs through ASAs for 3 locations. (1 HQ, 2 remote sites) I think I have the general config down. Fortunately, the ASDM makes it, or seems to...
Dear all,
I am having issues with my Cisco ASA 5505 for more than a month and it has been quite frustrating. I am trying to implement SSL-VPN client on ASA 5505 and when I perform a test p...
I setup the Cisco ASA 5505 with the VPN wizard and while it connects from the outside it causes the clients to loose DNS and will not allow them to connect to the server or drive shares. Here ...
Hello experts,
I'm hoping someone can shed some lights here to my question.
We have a Cisco 871 router setup for Easy VPN through a wizard to connect to a Cisco UC 520 device.
It work...
I have set up a Linksys RVS4000 with a static IP.
When trying to connect to the router remotely with the QuickVPN client, I'm getting stuck at "Verifying Network".
I'm trying this on two...
I have a Sonicwall 2040 and DHCP is provided by our DC.
I attempt to connect to our VPN using the SonicWall Global VPN client (version 3.1.0.556) and am prompted to enter my username and p...
