I currently have a PBX connected to the voice card in the 7204. The voice traffic is going over VoATM with encapsulation aal5mux voice. To cut cost I want to add a private line DS3 to the 7204 and ...
http://www.experts-exchange.com/Networking/Telecommunications/IP_Telephony/VoIP/Q_23667729...
Hello,
Is it possible to mirror a routed link to another port via SPAN?
I have a Ethernet connection via Verizon. My router is marked with QoS DiffServ value and Verizon says that they do not...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Switches/Q_23689553.html
Here's the problem.
Field device connected to an ATM cloud using DSL.
Field device has an ip of 10.10.1.226/24 with a gateway of 10.10.1.254. 10.10.1.254 is assigned to a BVI interface. BVI1 ...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21519964.html
Zones:
RoutersDate Answered: 08/24/2005 Grade: A Views: 0
Hey !
Putting a co-located DC design together for a client. basic topology below
E3 Primary E3 Secondary
l ...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21570462.html
Zones:
RoutersDate Answered: 09/22/2005 Grade: A Views: 4
I have a Cisco 7206 VXR in Site b with a multi-channel DS3 and at Site A, I have a cisco 3845 with 2 T1 lines.
From the attchement, this is massive Drops and flushes caused by congestion, etc.
He...
http://www.experts-exchange.com/Networking/Broadband/ISPs/Q_23833654.html
Dear all,
I have got a CISCO 7206 and there is an entire T3 being used. What is the best way to determine when a T1 goes down and when it comes up on any particular serial interface .. I have en...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21355325.html
Zones:
RoutersDate Answered: 03/18/2005 Grade: A Views: 0
We're trying to figure out if this can work, and if so, how to do it:
We'd like to run two DS1 circuits to an A-location where there would be a 2600 series Cisco router. Then, for our Z-locatio...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21430482.html
Zones:
RoutersDate Answered: 05/20/2005 Grade: A Views: 0
I have a 7206 XVR with mutilple T1's termintated by an 8 port T1 PA. I am using MPPP to bind the T1's.
We are are upgrade bandwidth to 15 meg by bringing in a DS3 capped at 15 meg. I am going to...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21631317.html
Zones:
RoutersDate Answered: 11/15/2005 Grade: A Views: 0
I am currently running 20 T1's through a Multi Channel T3 Card in a 7206 VXR Router. The VXR Router has an Asterisk PBX Connected to it through a PA-4E (4 Port 10MHZ) Interface. One of the T1's r...
http://www.experts-exchange.com/Networking/Misc/Q_22073485.html
I have 2 7206 routers with one as a Cold standby. i want to implement GLBP and have already changed my external public ips to a /29 to allow for the masquerading that must take place. I have availa...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_23363768.html
