Advertisement

Check out our new and improved Advanced Search! We have added additional search options and the ability to save your searches.
 
Enter Keywords:
 
1 - 10 of 94(0.011 seconds)
[x]
The Solution Rating System

With so many solutions, how can you tell which solutions are most likely to help you and which ones are not? To provide you with a tool to use, we rate our solutions based on various elements that most accurately determine if a solution is a quality solution. To explain what factors affect the solution rating, here are the elements we take into consideration when formulating our solution rating.

  • The Grade of the Solution
  • The Zone Rank of the Expert Providing the Solution
  • The Number of Author and Expert Comments
  • The Number of Experts Contributing
  • The Feedback of the Community

Your Input Matters
Because of the way the system is set up, the most important variable in this equation is you. As a member of Experts Exchange, you are able to cast your vote on the quality of the solutions in regard to how complete, accurate, helpful and easy to understand each solution is. When you provide your feedback, each rating is adjusted accordingly. So, if you see a solution that has a poor rating that you think is a good solution, let us know by rating it. As you do, the rating will be adjusted and will become more accurate for other members of our site.

If you have any suggestions that you would like to make for our rating system, please ask a question in the Suggestions Zone of Community Support.

Thank you!

8.7
Once I reset my ASA 5505 to the factory default, I either don't have the right device IP address (tried 192.168.1.1)  and/or the wrong username and password.  I tried leaving both blank, then I tri...
Zones: Cisco PIX Firewall, H...Date Answered: 07/31/2008 Views: 329
I have a Cisco ASA 5505 Firewall behind a Netopia DSL Router.  I'm new to Cisco firewalls but since they had a Start up Wizard I figured it would be no problem, famous last words.  So I used the st...
Zones: Cisco PIX Firewall, H...Date Answered: 01/27/2008 Views: 0
I bought a Firewall ASA-505 and after many procedures was impossible to configure it correctly. The static IP address is ok, is providing correctly the internal IP address, the firmware version is ...
Zones: Hardware Firewalls, VPN, Cisc...Date Answered: 04/21/2008 Views: 14
Hello all: I am trying to get 3 internal networks out to the internet. The 192.x.x.x can access the internet, but not the 10.x.x.x network. I want no communication between the networks, which fr...
Zones: Network Operations, Networking, TCP/IPDate Answered: 03/22/2008 Views: 0
Hi there, I'm a relative newbie when it comes to Cisco products. I've finished about half of the CCNA certification manual (Sybex), so have a bit of familiarity with the CLI. I've been asked...
Zones: Cisco PIX FirewallDate Answered: 03/05/2009 Views: 18
I can't open some ports in my new firewall Cisco ASA 5505. I wish to permit the traffic form the outside to one pc on my lan. The pc Ip on the lan is 192.168.1.4 and I wisht to open port 4662 TCP a...
Zones: Cisco PIX Firewall, H...Date Answered: 03/28/2008 Views: 21
I have a Cisco ASA 5505 firewall install on my network.  Ports 21, 25, 80 and 443 are showing up a open ports when I run Shields Up! from www.grc.com.  What do I need to do to make these ports stea...
Zones: Cisco PIX FirewallDate Answered: 04/03/2008 Views: 0
Could some take a look at my running configuration and let me know if everything looks secure?  We got a Network Alert - Open Proxy email from our ISP.  The email says that they have received a rep...
Zones: Hardware FirewallsDate Answered: 04/03/2008 Views: 0
We just installed a Cisco ASA 5505 (basic license, 50 user)  to protect our network and support VPN connectivity for remote clients. We also have set up a DMZ for a wireless network on site used by...
Zones: Cisco PIX Firewall, VPN, Hard...Date Answered: 05/04/2008 Views: 0
I only have the capability of connecting to an ASA 5505 through the ASDM 5.2 software. What is the equivalent of Show running config in this program?  I need to get the configuration off of the box...
Zones: Hardware Firewalls, Routers, Cisco PI...Date Answered: 05/20/2008 Views: 0