Advertisement

Check out our new and improved Advanced Search! We have added additional search options and the ability to save your searches.
 
Enter Keywords:
 
1 - 10 of 280(0.001 seconds)
[x]
The Solution Rating System

With so many solutions, how can you tell which solutions are most likely to help you and which ones are not? To provide you with a tool to use, we rate our solutions based on various elements that most accurately determine if a solution is a quality solution. To explain what factors affect the solution rating, here are the elements we take into consideration when formulating our solution rating.

  • The Grade of the Solution
  • The Zone Rank of the Expert Providing the Solution
  • The Number of Author and Expert Comments
  • The Number of Experts Contributing
  • The Feedback of the Community

Your Input Matters
Because of the way the system is set up, the most important variable in this equation is you. As a member of Experts Exchange, you are able to cast your vote on the quality of the solutions in regard to how complete, accurate, helpful and easy to understand each solution is. When you provide your feedback, each rating is adjusted accordingly. So, if you see a solution that has a poor rating that you think is a good solution, let us know by rating it. As you do, the rating will be adjusted and will become more accurate for other members of our site.

If you have any suggestions that you would like to make for our rating system, please ask a question in the Suggestions Zone of Community Support.

Thank you!

7.6
This what I want to do, 67.x.x.1 to 67.x.x.255 So I have public Ip addresses I would like to add a (Eth 3) so I can control all of the outside ip addresses going out from the pix vs. having a...
Zones: Security, Routers, Cisco PIX FirewallDate Answered: 02/22/2008 Views: 0
I am having trouble configuring my firewalls for failover. I have two identical Cisco PIX 515E firewalls connected by a failover cable. They are both connected to a Cisco switch via Cat5. I have tr...
Zones: Networking, Hardware Firewalls, Consumer Fi...Date Answered: 08/26/2003 Views: 0
I am the IT for a small company, and have recently aquired a cisco pix 515e. I have looked over quite a bit of documentation, but i cannot find the way to access the GUI to start looking inside. Ca...
Zones: RoutersDate Answered: 05/10/2004 Views: 0
Hello everyone, I really love this site so I decided to join to help with learning Cisco in more depth.  Was hoping I could get someone to proof my configs to confirm they will pass traffic correct...
Zones: Networking, Hardware Firewalls, Switches...Date Answered: 06/23/2004 Views: 0
Anyone know if this device supports UPnP NAT?   Cisco PIX Firewall Version 6.1(4) Cisco PIX Device Manager Version 1.1(2) Compiled on Tue 21-May-02 08:40 by morlee idmdpix up 130 days 17 ...
Zones: Networking, Hardware Firewalls, Cisco PIX F...Date Answered: 07/07/2004 Views: 0
I am using the following configuration on my firewall; PIX Version 6.3(3) interface ethernet0 100full interface ethernet1 100full interface ethernet1 vlan21 physical interface ethernet1 vlan...
Zones: Software Firewalls, Ent...Date Answered: 09/15/2004 Views: 0
I have a cisco pix 515e that I am having to work on.  I am using the PDM v2.1 because the telnet side has a password that no one knows.  anyways, my problem is that every time I create a rule to ma...
Zones: Software Firewalls, Ent...Date Answered: 10/29/2004 Views: 0
I am trying to reconfigure a couple of PIX firewalls.  Basically, I'm just trying to remove some extraneous statements that are no longer needed.  I am quite familiar with Cisco 26xx and 36xx route...
Zones: Software Firewalls, C...Date Answered: 01/12/2005 Views: 15
We are trying to setup a Cisco pix 515e on our network.  We are not using the dmz as of right now, we will eventually migrate over to that.  For now we have the need to just use inside,outside inte...
Zones: Software Firewalls, Ent...Date Answered: 03/02/2005 Views: 0
I want to put an exclusion in the firewall so people cannot access sites like weatherbug or webshots, how do I do that, the Cisco software of the firewall shows ASDM 5.0. Thanks!
Zones: Networking, Hardware Firewalls, DHCPDate Answered: 10/14/2005 Views: 5