I have a Cisco 3660 router and T1 connections from 4 Different providers. What is the best way to configure the routers so that traffic goes to the fastest carrier to a particular destination?
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_11055743.html
Zones:
RoutersDate Answered: 09/09/2000 Grade: C Views: 0
I have met a problem when I configured a CISCO 2610 router.I used 1 Serial on WAN Slot 0,and 8 Async network module(8 Anolog Modem) on Slot 1.The Ethernet Address I used is 192.168.1.254 255.255.25...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_11180251.html
Zones:
RoutersDate Answered: 11/30/2000 Grade: B Views: 0
Hi everyone,
Is there anyway one can query a CISCO 2501 on the actual rate that a synchronous serial port is being clocked?
I have a 2501 with 2 X.21 synchronous serial ports. I've requested ou...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_11481718.html
Zones:
RoutersDate Answered: 10/15/2000 Grade: B Views: 0
Is there any way I can use a Cisco router to block a users machine's MAC address from going out on the Internet. I know I can do this with third party software like Zone Alarm.
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_11518138.html
Zones:
RoutersDate Answered: 10/23/2000 Grade: B Views: 0
7206 128 meg RAM 12.1-3T IOS
BGP full routes from one provider
Sprint specific from sprint
I have setup ethernet 0/1 with the following items.
interface Ethernet1/0
description >> Connec...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_11718038.html
Zones:
RoutersDate Answered: 07/18/2001 Grade: A Views: 0
I have 22 production Cisco 5000s and one spare Cisco 5000. Most of my units have 12 port boards in them. Our organinzation recently started buying new 24 port (WS-X5224) boards.
When I load one of...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_20080685.html
Zones:
RoutersDate Answered: 07/14/2001 Grade: B Views: 0
I have a Cisco 2600 router (2 Serial WICs + 1 Ethernet 10bT). Serial 0 is connected to an internal network, Serial 1 is connected to the internet.
My problem is I need to have all internet traffi...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_20090440.html
Zones:
RoutersDate Answered: 07/24/2001 Grade: A Views: 0
We have a couple of Cisco routers at the end of an HDLC leased line. We are using Service provider DTUs to terminate the line, and have CAB-X21-MT cables connected to these devices on the serial p...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_20099680.html
Zones:
RoutersDate Answered: 04/03/2001 Grade: A Views: 0
I need to know what command to use so that I can figure out what IP addresses my dsl users who are set up on virtual circuits on my router are getting. I can currently look at logs to view hardwar...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_20101667.html
Zones:
RoutersDate Answered: 08/12/2001 Grade: A Views: 0
We've developed some programs based on NetFlow running on Cisco 7507,and we plan to change our router to 6509.Does 6509 support NetFlow?
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_20125781.html
Zones:
RoutersDate Answered: 06/09/2001 Grade: B Views: 0
