Advertisement

Check out our new and improved Advanced Search! We have added additional search options and the ability to save your searches.
 
Enter Keywords:
 
1 - 10 of 17823(0.171 seconds)
[x]
The Solution Rating System

With so many solutions, how can you tell which solutions are most likely to help you and which ones are not? To provide you with a tool to use, we rate our solutions based on various elements that most accurately determine if a solution is a quality solution. To explain what factors affect the solution rating, here are the elements we take into consideration when formulating our solution rating.

  • The Grade of the Solution
  • The Zone Rank of the Expert Providing the Solution
  • The Number of Author and Expert Comments
  • The Number of Experts Contributing
  • The Feedback of the Community

Your Input Matters
Because of the way the system is set up, the most important variable in this equation is you. As a member of Experts Exchange, you are able to cast your vote on the quality of the solutions in regard to how complete, accurate, helpful and easy to understand each solution is. When you provide your feedback, each rating is adjusted accordingly. So, if you see a solution that has a poor rating that you think is a good solution, let us know by rating it. As you do, the rating will be adjusted and will become more accurate for other members of our site.

If you have any suggestions that you would like to make for our rating system, please ask a question in the Suggestions Zone of Community Support.

Thank you!

6.0
I have a Cisco 3660 router and T1 connections from 4 Different providers.  What is the best way to configure the routers so that traffic goes to the fastest carrier to a particular destination?
Zones: RoutersDate Answered: 09/09/2000 Views: 0
I have met a problem when I configured a CISCO 2610 router.I used 1 Serial on WAN Slot 0,and 8 Async network module(8 Anolog Modem) on Slot 1.The Ethernet Address I used is 192.168.1.254 255.255.25...
Zones: RoutersDate Answered: 11/30/2000 Views: 8
Hi everyone, Is there anyway one can query a CISCO 2501 on the actual rate that a synchronous serial port is being clocked? I have a 2501 with 2 X.21 synchronous serial ports. I've requested ou...
Zones: RoutersDate Answered: 10/15/2000 Views: 0
Is there any way I can use a Cisco router to block a users machine's MAC address from going out on the Internet.  I know I can do this with third party software like Zone Alarm.
Zones: RoutersDate Answered: 10/23/2000 Views: 0
7206 128 meg RAM 12.1-3T IOS BGP full routes from one provider Sprint specific from sprint I have setup ethernet 0/1 with the following items. interface Ethernet1/0  description >> Connec...
Zones: RoutersDate Answered: 07/18/2001 Views: 8
I have 22 production Cisco 5000s and one spare Cisco 5000. Most of my units have 12 port boards in them. Our organinzation recently started buying new 24 port (WS-X5224) boards. When I load one of...
Zones: RoutersDate Answered: 07/14/2001 Views: 0
I have a Cisco 2600 router (2 Serial WICs + 1 Ethernet 10bT).  Serial 0 is connected to an internal network, Serial 1 is connected to the internet. My problem is I need to have all internet traffi...
Zones: RoutersDate Answered: 07/24/2001 Views: 0
We have a couple of Cisco routers at the end of an HDLC leased line.  We are using Service provider DTUs to terminate the line, and have CAB-X21-MT cables connected to these devices on the serial p...
Zones: RoutersDate Answered: 04/03/2001 Views: 4
I need to know what command to use so that I can figure out what IP addresses my dsl users who are set up on virtual circuits on my router are getting.  I can currently look at logs to view hardwar...
Zones: RoutersDate Answered: 08/12/2001 Views: 0
We've developed some programs based on NetFlow running on Cisco 7507,and we plan to change our router to 6509.Does 6509 support NetFlow?
Zones: RoutersDate Answered: 06/09/2001 Views: 0