When I enter my routers WAN/IP or use its associated DynamicDNS name, instead of hitting the web page I have running on IIS, i get the Cisco SDM prompting me for password. I have a static NAT st...
http://www.experts-exchange.com/Networking/Misc/Q_21794069.html
very new to cisco routers here, so i'll try as best that i can..
our network now:
older router = 38.154.x.1
older router = 192.168.10.1
the network'd comptuers are connected to the old rout...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21828400.html
Zones:
RoutersDate Answered: 06/03/2006 Rating: 6.8 Views: 0
brought a used cisco 3725 with an IOS ver 12.2(15)T5
according to the SDM installation the SDM supported IOS versions are 12.2(11)T6 or later 12.3(2)T or later 12.3(1)M or later 12.3(4)XD 12.2(1...
http://www.experts-exchange.com/Networking/Misc/Q_21885959.html
Zones:
Networking,
FTPDate Answered: 06/14/2006 Rating: 9.0 Views: 0
I am using a Cisco 2811 router with a vwic2-2mft-t1 module and everything works fine. The only thing is that the interface created by the module (serial 0/1/0:0) does not show up in the SDM GUI. ...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_22602829.html
Zones:
RoutersDate Answered: 06/01/2007 Rating: 9.0 Views: 0
Hi,
I bouth a new router and it comes with a cisco SDM v 2.4. I couldn't install this CD at all. Every time I try to install, it says "Windows cannot access specified device, or file. You may n...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_22961788.html
Zones:
RoutersDate Answered: 11/15/2007 Rating: 7.4 Views: 14
I have a router that's already in production and was initially configured with CLI, how can i enable SDM on it?
i looked in the flash and the files are there for SDM..thanks
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_23865890.html
Zones:
RoutersDate Answered: 11/03/2008 Rating: 8.2 Views: 0
Need help with a Cisco 871 configuration, I have a new router to be used with Firewall and port forwarding to 2 servers. my issue is I have about 15 ports to forward to one internal IP for a POS ap...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Firewalls/Q_24202059.html
i have a Cisco 877 modem router which i have factory reset. i have enabled HTTP and HTTPS on the router using a console cable, to allow me to use SDM. i have installed SDM v24 on both the computer ...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_24391231.html
Zones:
Routers,
ModemsDate Answered: 05/07/2009 Rating: 9.3 Views: 8
I'm having a problem with the cisco sdm. It's installed correctly, I've configured my router with the following:
ip http server
ip http secure-server
ip http authentication local
ip http timeo...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_24537638.html
Zones:
RoutersDate Answered: 07/13/2009 Rating: 9.3 Views: 0
I use Cisco SDM to monitor my router and for some minor configurations. Recently I tried to setup VPN and when I click on the "Launch the selected task" I get nothing. The button acts as if it is a...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_24736459.html
