I'm looking to setup a internet connection with fault tolerance, so I've decided to purchase a T1 and an ADSL connection through the same ISP and use BGP routing.
I've been told I need to purcha...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_20115572.html
Zones:
RoutersDate Answered: 05/14/2001 Grade: A Views: 0
Hello,
My company has 2 T1's with different ISP's and a Cisco 3660 router with 2 serial interfaces and 2 fast ethernet ports. We're running different web services with the T1's. Ie: T1 A would...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_20545754.html
Zones:
RoutersDate Answered: 06/12/2003 Grade: A Views: 0
BGP experts, I have done quite a bit of research and come up with the below listed configuration. I will be multihoming with 2 ISP's and load sharing inbound and outbound.
Please verify that my co...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_20940504.html
Zones:
RoutersDate Answered: 04/01/2004 Grade: B Views: 0
I need to configure BGP v4 on my network, but I have only book/training knowledge of the protocol. Any resources out there I can use to make my first configuration with BGP a successful one? Also, ...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21328276.html
Zones:
RoutersDate Answered: 03/06/2005 Grade: A Views: 0
We have two Cisco 7204 routers each with a connection to a different ISP. We also have multiple networks that sit behind these routers on Cisco 6500s that consist of 6 publicly-addressed /24 prefix...
http://www.experts-exchange.com/Networking/Misc/Q_22021923.html
Zones:
NetworkingDate Answered: 10/16/2006 Grade: A Views: 0
I have EBGP deployed on my Cisco 3825 Routers. I am having Cisco 3750 in HSRP and OSPF Deployed in area o. The router also has OSPF in area 0. I am unable to redistribute routers from BGP to OSPF. ...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_22026341.html
Zones:
RoutersDate Answered: 10/18/2006 Grade: A Views: 87
Currently I have two routers located in two locations in my state, I have my AS number and I have set each router using the router bgp command. Both are Cisco 2800, Here is a summary:
I will cha...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_22097423.html
Zones:
RoutersDate Answered: 12/19/2006 Grade: A Views: 0
I have a several BGP sessions and i am using standard Access lists to filter which routes i announce.
For example i have a list call peering-out in my case i own most IP's except of 187.0 / 188.0 ...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_22580493.html
Zones:
RoutersDate Answered: 06/06/2007 Grade: A Views: 5
I currently have a couple sites that connect to an MPLS that uses BGP. I'm trying to figure out how the MPLS provider is getting my routes from Location 1, 2, and 3 to the other locations. Right...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_22852093.html
looking for a good BGP presentation...preferablly both slides and audio..
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_23327266.html
Zones:
RoutersDate Answered: 04/18/2008 Grade: A Views: 0
