Hello,
I'm currently studying for my CCNA 640-802 and I am working in a lab with a cisco 2950 24 port switch and a 2600 router. I am trying to set up intervlan routing, and have entered the foll...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_24310935.html
So far I've:
Made port 0/4 on the switch part of VLAN2.
Made port 24 on the switch the trunk link (this goes to my 2600 router)
I went to the 2600 router and did a
c2600(config)#int e0/0.1...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21129135.html
Zones:
RoutersDate Answered: 09/13/2004 Rating: 8.4 Views: 0
I have a Cisco 3750 and 2950 switch in my network. Trunking is enabled on the link that connects the 2950 to the 3750 switch with encap as dot1q.
One VLAN, viz. VLAN4, is configured in the 3750 ...
http://www.experts-exchange.com/Software/System_Utilities/Remote_Access/VPN/Q_21214927.htm...
Zones:
VPNDate Answered: 01/01/2006 Rating: 7.0 Views: 12
Hi,
I am using CISCO ROuter 3662 Model and IOS Ver:12.3(5b). I am trying to assign the 'encapsulation dot1q' on the LAN sub interface of the Router. But in router , it is shwoing an unknown co...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21325876.html
Zones:
RoutersDate Answered: 03/19/2005 Rating: 8.6 Views: 0
Hi all,
On monday we had an IDF on the floor go down. The fiber link from the IDF to the MDF was going up and down randomly and for no apparent reason. The IDF has a 3524XL and the front end i...
http://www.experts-exchange.com/Networking/Misc/Q_21548999.html
Hi,
I have a couple of problems I just noticed on a few switches and routers. I am getting alot of packet errors and discarded packets on certain interfaces. I suspect that I have not set the port...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21592270.html
Zones:
RoutersDate Answered: 03/09/2006 Rating: 9.4 Views: 25
We are implementing a PIX 506 into the network and also would like to subnet out the network to make things more efficient. Currently the setup is: ISP router ---- Cisco 1721 -- Catalyst 2950.
...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21805173.html
Zones:
RoutersDate Answered: 05/10/2006 Rating: 8.6 Views: 0
I have a 3800 series router with 4 switches daisy chained via fiber and we have EACH port on its own VLAN. We have given each port 60 usable IP addresses. Anything in the 10.0.0.0 Subnet is worki...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21828415.html
Zones:
RoutersDate Answered: 04/26/2006 Rating: 9.8 Views: 0
We have the config I am going to post below. I currently have 1 router and 4 switches hooked up to the router. Each port is a seperate VLAN and they can not see horizontally. They can only see t...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21883737.html
Zones:
RoutersDate Answered: 09/14/2006 Rating: 3.8 Views: 0
hi
iam setup new network with the below specification (i want to use router for inter-VLAN)
cisco router2800---------->ciscoswitch(2950)-------->PCs
for switch i made this configuration
2...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_22648721.html
Zones:
Routers,
...Date Answered: 06/22/2007 Rating: 9.8 Views: 51
