Hello,
I have a Cisco 3640 Router with IOS Image (c3640-js-mz.122-1c.bin). The router does not boot up, yet dumps you into the (rommon>) prompt.
When issuing a (dir flash:) command, I receiv...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_20862336.html
Zones:
RoutersDate Answered: 01/25/2004 Grade: A Views: 45
When i power up the switch I get this and it's looping indefinitely. I can't even get into Rommon. Is it because I don't have a valid image or the flash is corrupted. What can I do in this case?
...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21581958.html
Zones:
RoutersDate Answered: 10/05/2005 Grade: A Views: 0
I have delted the old IOS image from the 2948G-L3 and tried to copy from tftp the new image that I had. It said error opening tftp (not enough space). At that point I had over 13 Mb free and the ...
http://www.experts-exchange.com/Networking/Misc/Q_21803161.html
Zones:
NetworkingDate Answered: 04/07/2006 Grade: B Views: 0
System flash directory:
File Length Name/status
1 16032788 c2600-ik9o3s3-mz.123-6.bin
2 211640 crashinfo_19930301-032328
[16244556 bytes used, 8372 available, 16252928 total]
163...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21052724.html
Zones:
RoutersDate Answered: 07/14/2004 Grade: A Views: 33
Hi Guys,
I have an ASA5510 which boots to the rommon prompt, I have obtained a new image for the internal disk as it shows no image to boot from, I have connected a PC with TFTP runnin...
http://www.experts-exchange.com/Security/Software_Firewalls/Q_21594381.html
Hi,
I have a cisco 877 and was working just fine, but today suddenly crash...
I can only have access to rommon mode when it started... as far as i read it's a matter of corrupted flash. and ...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_21636908.html
Zones:
RoutersDate Answered: 03/09/2006 Grade: A Views: 13
This is the error i get when my router reboots:
open: file "c2600-i-mz.121-2.bin" not found
open(): Open Error = -1
loadprog: error - on file open
boot: cannot load "flash:"
Any ideas? Thi...
http://www.experts-exchange.com/Networking/Misc/Q_21962425.html
Zones:
Networking,
FTPDate Answered: 08/30/2006 Grade: B Views: 4
Router starts from bootstrap correctly with no errors. It then asks if I want to do the initial config , I do that and end it with a copy running-config startup-config. Router is then cold rebooted...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_22645654.html
When I boot up my 2600 I get a wierd message.
Here it is:
System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for i...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_20295684.html
Zones:
RoutersDate Answered: 01/12/2003 Grade: A Views: 0
I have a 3640 with a corrupt flash
i have xmodem a new ios over to the 3640
but when i reboot the router it comes up in rommon again
am i missing something?
this is what rommon says:
System ...
http://www.experts-exchange.com/Hardware/Networking_Hardware/Routers/Q_20569573.html
Zones:
RoutersDate Answered: 06/22/2003 Grade: A Views: 57
