?
Solved

lpd setup with hp jetdirect ex3 external print server

Posted on 1997-07-29
4
Medium Priority
?
488 Views
Last Modified: 2013-12-23
I am trying to setup my jetdirect ex3 to print using lpd. I have
tcp/ip up and running on my nt server 4.0 w/ sp 3. I have installed tcp print services on the server. I "route added" the default ip address of the ex 3 to the server routing table.
I do a "route print" and the address 192.0.0.192 is shown.
The dlc protocal works fine with the ex3. I followed the instructions from HP fax-back help. But when I ping 192.0.0.192 from the server the ping times out. The server
does have (2) ip addresses. One for the internal network,
 and one from the ISP for access to the internet.I "route added" the 192.0.0.192 to the internal ip address. Any suggestions? Thanking you in advance
Luis@BTR-Architects.com
0
Comment
Question by:luisluna
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
4 Comments
 
LVL 2

Expert Comment

by:jmj050997
ID: 1562543
- You 'd better change the default ex3 ip address to one address on your subnet.

- An other solution would be to add the ip address 192.0.0.193 to your server in the Network control panel applet, protocol, TCP/ip, properties, Advanced. (Note the 193)
You may have to reboot before ping works


0
 

Author Comment

by:luisluna
ID: 1562544
The "arp" solution I recieved from vmj worked, I did what jmj suggests and that did not work. thanks
0
 

Expert Comment

by:bgoldstein
ID: 1562545
You mention the "default" address of the jet direct card.  I presume 192.0.0.192 is the address of the jet direct card.

Try running tracert from the NT server to 192.0.0.192 and see where the packet goes.  It may not be pointed in the right direction.  Or, it may be going in the right direction, but being ignored by the jet direct card.  Either case will tell a story.

It would useful to know what IP addresses you are using on the NT server and your internal network.  That way I can give you the proper IP command to make this work.
0
 

Accepted Solution

by:
elkerliek earned 200 total points
ID: 1562546
Did you add the Jetdirect printer port to NT?
I think it's in HP Jetadmin for NT (free)

You can change the setup of the jetdirect box/card, ans the ip-adres.

0

Featured Post

Prepare for your VMware VCP6-DCV exam.

Josh Coen and Jason Langer have prepared the latest edition of VCP study guide. Both authors have been working in the IT field for more than a decade, and both hold VMware certifications. This 163-page guide covers all 10 of the exam blueprint sections.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

FIPS stands for the Federal Information Processing Standardisation and FIPS 140-2 is a collection of standards that are generically associated with hardware and software cryptography. In most cases, people can refer to this as the method of encrypti…
Trying to figure out group policy inheritance and which settings apply where can be a chore.  Here's a very simple summary I've written which might help.  Keep in mind, this is just a high-level conceptual overview where I try to avoid getting bogge…
Michael from AdRem Software explains how to view the most utilized and worst performing nodes in your network, by accessing the Top Charts view in NetCrunch network monitor (https://www.adremsoft.com/). Top Charts is a view in which you can set seve…
Add bar graphs to Access queries using Unicode block characters. Graphs appear on every record in the color you want. Give life to numbers. Hopes this gives you ideas on visualizing your data in new ways ~ Create a calculated field in a query: …

777 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question