[Webinar] Streamline your web hosting managementRegister Today

x
?
Solved

kyocera 1200s

Posted on 1998-07-05
6
Medium Priority
?
189 Views
Last Modified: 2010-04-12
I have recently aquired a Kyocera F-1200S laser printer ( pretty old!) and I'm trying to find specifications / manual for it. I've visited the Kyocera page but can find no reference to it there. Any ideas where I might find this information?
0
Comment
Question by:RHarrison
  • 3
  • 3
6 Comments
 
LVL 1

Accepted Solution

by:
ACScomm earned 600 total points
ID: 2014532
Well as you said, your printer is pretty old!... the launch date was 1990...
There is some info for you about your Kyocera F-1200S printer :
Speed: 10 ppm cut sheet
Technique: Laser electrophotographic.
Resolution: 300×300 dpi
Fonts: 79 resident bitmap fonts
Emulations: Lineprinter
Interfaces: RS-232C Centronics parallel
Memory : with no additional memory SIMMs : 512 K
               You can add additional memory to your printer, how to do it :
               ( the memory SIMMs are : JetRam-01Z )
                { Each expansion board has four banks made up of two slots each. SIMMs
                must be used in pairs. The two matching SIMMs (1MB of memory) are
                inserted into the slots of the same bank. If SIMMs are not inserted into the
                lowest numbered bank that is available, they will not work (i.e. fill the 1MB
                bank first, then the 2MB bank up to 4MB)}
                Prices of memory are about 1MB ~$90, 2MB ~$115, 4MB ~$160
If you need srivers for the printer look at this URL : http://www.kyocera.com/printers/drivers.html
If there is any more info you need, let me know.
ACScomm

0
 

Author Comment

by:RHarrison
ID: 2014533
Many thanks for the information, I hadn't realised it was so old, but at least it was VERY cheap!
Any ideas where I might obtain some more documentation for the thing
0
 
LVL 1

Expert Comment

by:ACScomm
ID: 2014534
Try to mail Kyocera's Product Information and General Inquiries costumers contact person, at the folowing Email address :  Maureen.Mandzik@kyocera.com
Ask her to send you any documentation you need directly.
0
Free Tool: Port Scanner

Check which ports are open to the outside world. Helps make sure that your firewall rules are working as intended.

One of a set of tools we are providing to everyone as a way of saying thank you for being a part of the community.

 

Author Comment

by:RHarrison
ID: 2014535
Thanks for the information it gives me a start. A couple of points -
1) any idea where I can get hold of some documentation for the printer?
2) can I increase memory by installing standard 1mb 30pin SIMMs?
0
 
LVL 1

Expert Comment

by:ACScomm
ID: 2014536
1- About documentation for the printer, well as I mentioned befor, you might mail Kyocera as I mentioned on my last comment, becouse there is a chance to get old manuals from Kyocera.
2- About installing memory SIMMs, I would only use SIMMs that fit your Kyocera printer i.e. SIMM model - JetRam-01Z , and dont forget to use the SIMMs in pairs.
0
 

Author Comment

by:RHarrison
ID: 2014537
Thanks for the info. I looked at the circuit board and it appears to have a special memory board installed.
I have also e-mailed Kyocera as you suggested. Awaiting reply
Many thanks for the help

0

Featured Post

Free Tool: Subnet Calculator

The subnet calculator helps you design networks by taking an IP address and network mask and returning information such as network, broadcast address, and host range.

One of a set of tools we're offering as a way of saying thank you for being a part of the community.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

This article shows how to get a list of available printers for display in a drop-down list, and then to use the selected printer to print an Access report or a Word document filled with Access data, using different syntax as needed for working with …
This tutorial is intended to teach the basics of 3-D Modeling using TinkerCad.com as the Computer Aided Drafting software. Once complete this model can be 3D printed.
In an interesting question (https://www.experts-exchange.com/questions/29008360/) here at Experts Exchange, a member asked how to split a single image into multiple images. The primary usage for this is to place many photographs on a flatbed scanner…
This video Micro Tutorial shows how to password-protect PDF files with free software. Many software products can do this, such as Adobe Acrobat (but not Adobe Reader), Nuance PaperPort, and Nuance Power PDF, but they are not free products. This vide…
Suggested Courses

612 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question