HPUX D-Class modem gettybleedindefs!
This weekk I av mostly been aving problems wiv modems!
I have a D class HP9000 running HP-UX 10.01 with an EISA mux card. I have configured a Multitech MT1432 modem and can use cu to dial out and connect to other systems.
Dialling in is another matter though, the system answers, negotiates and connects successfully at 9600 every time but I cannot get a login prompt or any other response and 30 seconds later the carrier drops.
I have included the gettydefs and inittab files below, perhaps one of you chaps could help me with this one, I think it has something to do with gettydefs but I can't see the wood for the trees now.
Thanks in advance..
J
gettydefs file....
9600m # B9600 HUPCL IGNPAR ICRNL IXON OPOST ONLCR CS8 CREAD
ISIG ICANON ECHO ECHOK ISTRIP IXANY TAB3
# B9600 SANE CS8 ISTRIP IXANY TAB3 HUPCL
#Modem login: #9600m
inittab entry...
a2:23:respawn:/usr/lbin/uu
dial in device file...
lssf /dev/ttyd2a2
eisa_mux0 card instance 2 port a2 ccitt callin at address 8/20/5/1 /dev/ttyd2a2
I have a D class HP9000 running HP-UX 10.01 with an EISA mux card. I have configured a Multitech MT1432 modem and can use cu to dial out and connect to other systems.
Dialling in is another matter though, the system answers, negotiates and connects successfully at 9600 every time but I cannot get a login prompt or any other response and 30 seconds later the carrier drops.
I have included the gettydefs and inittab files below, perhaps one of you chaps could help me with this one, I think it has something to do with gettydefs but I can't see the wood for the trees now.
Thanks in advance..
J
gettydefs file....
9600m # B9600 HUPCL IGNPAR ICRNL IXON OPOST ONLCR CS8 CREAD
ISIG ICANON ECHO ECHOK ISTRIP IXANY TAB3
# B9600 SANE CS8 ISTRIP IXANY TAB3 HUPCL
#Modem login: #9600m
inittab entry...
a2:23:respawn:/usr/lbin/uu
dial in device file...
lssf /dev/ttyd2a2
eisa_mux0 card instance 2 port a2 ccitt callin at address 8/20/5/1 /dev/ttyd2a2
ASKER
What's wrong with CCITT on 10.x?
I had a problem with the modem settings on Friday, the serial speeds have been modified and I now get a getty respawned.
I can now enter a userid but when I press return nothing happens (handshaking??).
I tried pressing break but it doesn't work.
Any ideas?
I had a problem with the modem settings on Friday, the serial speeds have been modified and I now get a getty respawned.
I can now enter a userid but when I press return nothing happens (handshaking??).
I tried pressing break but it doesn't work.
Any ideas?
ASKER
Thanks ecw, you're a wonderful human being!!!
CCITT is definately stuffed on 10.x, I removed the device file and recreated it and it worked, please post an answer here for your points.
I don't suppose you'd know why CCITT is shagged though and if there is a patch for it, just out of interest!
J :)
CCITT is definately stuffed on 10.x, I removed the device file and recreated it and it worked, please post an answer here for your points.
I don't suppose you'd know why CCITT is shagged though and if there is a patch for it, just out of interest!
J :)
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
don't use ccitt dial in, on HP-UX 9 it's fine, on 10.X, not so fine.
check that getty has grabbed the line after connection using ps. if the tty field is ttyd2a2 (not a ?), it has.
try sending a break to the hp after connection is established, this might kick it into life.