Still celebrating National IT Professionals Day with 3 months of free Premium Membership. Use Code ITDAY17

x
?
Solved

Just installed VPN Module....

Posted on 2000-05-10
9
Medium Priority
?
224 Views
Last Modified: 2010-04-17
I just installed a VPN module into a 1750 series router.  How do I know if this module is accessible to the router -or if it has been properly installed?  Doe show controllers do anything for me?  If so -what should I be looking for?
0
Comment
Question by:Silas
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
  • 2
  • 2
  • +3
9 Comments
 

Author Comment

by:Silas
ID: 2798350
Adjusted points from 100 to 200
0
 
LVL 3

Expert Comment

by:bartt
ID: 2799034
Silas it might be just a suggestion, maybe it's good to get your skills to CCNA
0
 

Author Comment

by:Silas
ID: 2800014
Bartt -I am a CCNA -the show controllers command does not to show you the vpn module.  This router is unlike a 2500 series one -and is hard to work on in terms of hardware installation. -Do you know the command?
0
Concerto Cloud for Software Providers & ISVs

Can Concerto Cloud Services help you focus on evolving your application offerings, while delivering the best cloud experience to your customers? From DevOps to revenue models and customer support, the answer is yes!

Learn how Concerto can help you.

 
LVL 3

Expert Comment

by:apadua
ID: 2803199
Perhaps show version? It usually shows ports and modules (at least on the 7513 it does...)


A.
0
 
LVL 3

Expert Comment

by:apadua
ID: 2835738
Any news?
0
 
LVL 5

Expert Comment

by:aioudine
ID: 2909765
TRY
r1750#show crypto engine configuration
0
 
LVL 5

Expert Comment

by:aioudine
ID: 2909774
Of couse you must have IOS with IPsec to work with VPN module
0
 
LVL 15

Expert Comment

by:jrhelgeson
ID: 3420490
What IOS version are you running? Please do a Show Ver for me.
What is the name (Cisco Part #) of the card you have installed.

Most likely you'll need to get an updated IOS version to support this card.  With this information, I will be able to tell you what minimum revision you'll need to support that module.

Thanks.

Joel
0
 

Accepted Solution

by:
smoss072100 earned 600 total points
ID: 3514152
0

Featured Post

Concerto Cloud for Software Providers & ISVs

Can Concerto Cloud Services help you focus on evolving your application offerings, while delivering the best cloud experience to your customers? From DevOps to revenue models and customer support, the answer is yes!

Learn how Concerto can help you.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

While it is possible to put two routes in place with the secondary having a higher metric, this may not always work. In the event of a failure that does not bring down the physical interface on the router the primary route is not removed. There is a…
Quality of Service (QoS) options are nearly endless when it comes to networks today. This article is merely one example of how it can be handled in a hub-n-spoke design using a 3-tier configuration.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

670 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question