Solved

net use with firewall... (what's the port?)

Posted on 2002-03-29
2
13,167 Views
Last Modified: 2013-11-29
Hi,

I'm running with XP, I was ennable my firewall. I would like to map my drive with another PC (win2k), using "Net use f: \\IP\share"

What's the port that I must open for that?
TCP 139 (in/out)?
and ...?

Thanks in advance...
(Apologize my english language...)
Phil !
0
Comment
Question by:samphi
2 Comments
 
LVL 63

Accepted Solution

by:
SysExpert earned 100 total points
ID: 6905496
(137,138,139)

also :

1220 » How do I establish a trust across a firewall? netbios ports

 You need to enable the following ports:

    PORT 135 (TCP or UDP) for the Remote Procedure Call (RPC) Service.
    PORT 137 (UDP) for the NetBIOS Name Service.
    PORT 138 (UDP) for NetBIOS datagram (Browsing).
    PORT 139 (TCP) for NetBIOS session (NET USE).
    ALL PORTS above 1024 for RPC Communication.

 See tip 0956 for using LMHOSTS for name resolution.

 NOTE: You would have multple IP_ADDRESS_OF_PDC PDCname #PRE #DOM:DomainName entries.

 If you use DNS and WINS, enable:

    PORT 53 (TCP and UDP) for DNS. DNS port
    PORT 42 (TCP and UDP) for WINS Replication. WINS port

 If you establish the trust through PPTP, enable:

    PORT (TCP) 1723 for PPTP.
    IP PROTOCOL 47 (GRE)

 For SMS Remote Helpdesk, enable:

    PORT (TCP) 1761 for Verification of Rights (IPX 0x8138).
    PORT (TCP) 1762 for Remote Control (IPX 0x8238).
    PORT (TCP) 1761 for Remote Reboot (IPX 0x8138).
    PORT (TCP) 1763 for Remote Chat (IPX 0x845F).
    PORT (TCP) 1764 for File Transfer (IPX 0x4100).
    PORT (TCP) 1761 for Remote Execute (IPX 0x8138).

---------------

I hope this helps !
0
 

Author Comment

by:samphi
ID: 6910474
Exellent!!! thank you very much !
0

Featured Post

PRTG Network Monitor: Intuitive Network Monitoring

Network Monitoring is essential to ensure that computer systems and network devices are running. Use PRTG to monitor LANs, servers, websites, applications and devices, bandwidth, virtual environments, remote systems, IoT, and many more. PRTG is easy to set up & use.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

#Citrix #Citrix Netscaler #HTTP Compression #Load Balance
Join Greg Farro and Ethan Banks from Packet Pushers (http://packetpushers.net/podcast/podcasts/pq-show-93-smart-network-monitoring-paessler-sponsored/) and Greg Ross from Paessler (https://www.paessler.com/prtg) for a discussion about smart network …
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

770 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question