Solved

How to obtain a new IP address using WinXP

Posted on 2002-06-15
2
214 Views
Last Modified: 2010-05-02
How do you obtain a new I.P. address using Windows XP. I can't find the winipcfg command anywhere and my computer will not connect to the internet.
0
Comment
Question by:Gmoney
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
2 Comments
 
LVL 4

Expert Comment

by:RichW
ID: 7080690
Try ipconfig from a Command box to see your IP addresses.
RichW
0
 
LVL 4

Accepted Solution

by:
RichW earned 50 total points
ID: 7080691
FROM WINDOWS XP HELP:

Ipconfig
Displays all current TCP/IP network configuration values and refreshes Dynamic Host Configuration Protocol (DHCP) and Domain Name System (DNS) settings. Used without parameters, ipconfig displays the IP address, subnet mask, and default gateway for all adapters.

Syntax
ipconfig [/all] [/renew [Adapter]] [/release [Adapter]] [/flushdns] [/displaydns] [/registerdns] [/showclassid Adapter] [/setclassid Adapter [ClassID]]

Parameters
/all
Displays the full TCP/IP configuration for all adapters. Without this parameter, ipconfig displays only the IP address, subnet mask, and default gateway values for each adapter. Adapters can represent physical interfaces, such as installed network adapters, or logical interfaces, such as dial-up connections.
/renew [Adapter]
Renews DHCP configuration for all adapters (if an adapter is not specified) or for a specific adapter if the Adapter parameter is included. This parameter is available only on computers with adapters that are configured to obtain an IP address automatically. To specify an adapter name, type the adapter name that appears when you use ipconfig without parameters.
/release [Adapter]
Sends a DHCPRELEASE message to the DHCP server to release the current DHCP configuration and discard the IP address configuration for either all adapters (if an adapter is not specified) or for a specific adapter if the Adapter parameter is included. This parameter disables TCP/IP for adapters configured to obtain an IP address automatically. To specify an adapter name, type the adapter name that appears when you use ipconfig without parameters.
/flushdns
Flushes and resets the contents of the DNS client resolver cache. During DNS troubleshooting, you can use this procedure to discard negative cache entries from the cache, as well as any other entries that have been added dynamically.
/displaydns
Displays the contents of the DNS client resolver cache, which includes both entries preloaded from the local Hosts file and any recently obtained resource records for name queries resolved by the computer. The DNS Client service uses this information to resolve frequently queried names quickly, before querying its configured DNS servers.
/registerdns
Initiates manual dynamic registration for the DNS names and IP addresses that are configured at a computer. You can use this parameter to troubleshoot a failed DNS name registration or resolve a dynamic update problem between a client and the DNS server without rebooting the client computer. The DNS settings in the advanced properties of the TCP/IP protocol determine which names are registered in DNS.
/showclassid Adapter
Displays the DHCP class ID for a specified adapter. To see the DHCP class ID for all adapters, use the asterisk (*) wildcard character in place of Adapter. This parameter is available only on computers with adapters that are configured to obtain an IP address automatically.
/setclassid Adapter [ClassID]
Configures the DHCP class ID for a specified adapter. To set the DHCP class ID for all adapters, use the asterisk (*) wildcard character in place of Adapter. This parameter is available only on computers with adapters that are configured to obtain an IP address automatically. If a DHCP class ID is not specified, the current class ID is removed.
/?
Displays help at the command prompt.
Remarks
The ipconfig command is the command-line equivalent to the winipcfg command, which is available in Windows Millennium Edition, Windows 98, and Windows 95. Although Windows XP does not include a graphical equivalent to the winipcfg command, you can use Network Connections to view and renew an IP address. To do this, open Network Connections, right-click a network connection, click Status, and then click the Support tab.
This command is most useful on computers that are configured to obtain an IP address automatically. This enables users to determine which TCP/IP configuration values have been configured by DHCP, Automatic Private IP Addressing (APIPA), or an alternate configuration.
If the Adapter name contains any spaces, use quotation marks around the adapter name (that is, "Adapter Name").
For adapter names, ipconfig supports the use of the asterisk (*) wildcard character to specify either adapters with names that begin with a specified string or adapters with names that contain a specified string. For example, Local* matches all adapters that start with the string Local and *Con* matches all adapters that contain the string Con.
0

Featured Post

Instantly Create Instructional Tutorials

Contextual Guidance at the moment of need helps your employees adopt to new software or processes instantly. Boost knowledge retention and employee engagement step-by-step with one easy solution.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

I’ve seen a number of people looking for examples of how to access web services from VB6.  I’ve been using a test harness I built in VB6 (using many resources I found online) that I use for small projects to work out how to communicate with web serv…
If you have ever used Microsoft Word then you know that it has a good spell checker and it may have occurred to you that the ability to check spelling might be a nice piece of functionality to add to certain applications of yours. Well the code that…
Show developers how to use a criteria form to limit the data that appears on an Access report. It is a common requirement that users can specify the criteria for a report at runtime. The easiest way to accomplish this is using a criteria form that a…
This lesson covers basic error handling code in Microsoft Excel using VBA. This is the first lesson in a 3-part series that uses code to loop through an Excel spreadsheet in VBA and then fix errors, taking advantage of error handling code. This l…

730 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question