Solved

Help, When I try to launch Exchange System Manager,my pc freeze ...

Posted on 2002-06-20
6
438 Views
Last Modified: 2013-12-03
have installed a domain controller (Win2k Sp2),configuring the Active Directory.
Then I've installed Exchange 2000 server but when I try to launch the ESM (Exchange System Manger),my pc freeze and all I can do is to reset my computer.
After that,I decided to reintall the domain controller but the problem remains.
I really need help,please.

Thank you.

Differents informations :
The DC is a multihomed computer.
I use 2000 server Sp2,and exchange 2000 corporate (typical installation).
0
Comment
Question by:bigstyle
  • 3
6 Comments
 
LVL 10

Expert Comment

by:kevala
ID: 7096735
What is going on the application and system logs? Are there any errors referencing Exchange?

I kinda find it hard to believe that ESM (application in user mode) is causing a server to freeze (Kernel mode)
0
 

Author Comment

by:bigstyle
ID: 7096907
Me neither I really dont understant.

Moreover,I started two times from scratch,but the problem remain.

In the application and system logs,I haven't got any error except one referencing the eventid 101 about the NNTP service but apparently it's not really a problem (one service which starts before another by reading the KB)

All I did is,
-install windows 2000 server

-configure my dns (primary zone,allow dynamic registration,delete the "internet" interface...)

-run dcpromo and dont let him configure my DNS.

-install few programs like winzip,messenger...

-I test my DC,by adding computers in the network,etc...everything seems to be ok.

-install exchange 2000 serveur,running before a /forestprep and /domainprep ,then a typical installation.
No error during the installation.

-When the installation is finished,I launch Exchange Sytem Manager and my pc freeze...

I have seen that a disk M: is created and for some directories, the access is forbidden although I am in the appropriate group.
I don't know if it's normal but I'm gonna be crazy :)

Thanks for all.
Fred



 
0
 

Author Comment

by:bigstyle
ID: 7097062
Me neither I really dont understant.

Moreover,I started two times from scratch,but the problem remain.

In the application and system logs,I haven't got any error except one referencing the eventid 101 about the NNTP service but apparently it's not really a problem (one service which starts before another by reading the KB)

All I did is,
-install windows 2000 server

-configure my dns (primary zone,allow dynamic registration,delete the "internet" interface...)

-run dcpromo and dont let him configure my DNS.

-install few programs like winzip,messenger...

-I test my DC,by adding computers in the network,etc...everything seems to be ok.

-install exchange 2000 serveur,running before a /forestprep and /domainprep ,then a typical installation.
No error during the installation.

-When the installation is finished,I launch Exchange Sytem Manager and my pc freeze...

I have seen that a disk M: is created and for some directories, the access is forbidden although I am in the appropriate group.
I don't know if it's normal but I'm gonna be crazy :)

Thanks for all.
Fred



 
0
 

Accepted Solution

by:
bigstyle earned 0 total points
ID: 9747099
Finally I found the solution myself.

My admin login was with a space blank (like xxx yyy) and all the problem was that.
0

Featured Post

Best Practices: Disaster Recovery Testing

Besides backup, any IT division should have a disaster recovery plan. You will find a few tips below relating to the development of such a plan and to what issues one should pay special attention in the course of backup planning.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Exchange server is not supported in any cloud-hosted platform (other than Azure with Azure Premium Storage).
This article explains in simple steps how to renew expiring Exchange Server Internal Transport Certificate.
In this video we show how to create a Resource Mailbox in Exchange 2013. We show this process by using the Exchange Admin Center. Log into Exchange Admin Center.: Navigate to the Recipients >> Resources tab.: "Recipients" is our default selection …
In this Micro Video tutorial you will learn the basics about Database Availability Groups and How to configure one using a live Exchange Server Environment. The video tutorial explains the basics of the Exchange server Database Availability grou…

777 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question