?
Solved

Cisco 803 Password problem.............

Posted on 2003-03-03
3
Medium Priority
?
592 Views
Last Modified: 2009-12-16
I fogot my passwords...Then through Password Recovery Procedure (http://www.cisco.com/warp/public/474/pswdrec_800.html). I Reset my router, its in boot# . from here i type boot at the boot#> prompt .its not initialize..........other than SET command.....Its not Recognize any command....
Please help.....what i have to do?


0
Comment
Question by:ponsuresh
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
3 Comments
 
LVL 18

Accepted Solution

by:
chicagoan earned 300 total points
ID: 8056682
You are blocked in Tiny-Rom.
Follow the procedures at http://www.cisco.com/warp/public/130/recovery_c800.html
0
 

Author Comment

by:ponsuresh
ID: 8062664
Thanks, Now my router working....but i getting error Message like this..

Auto-boot: failed, "no such file"


TinyROM version 1.2(2)
16:22 08/02/99
Copyright (c) 1998-1999 by cisco Systems, Inc.
All rights reserved.

POST ......... OK.  4MB DRAM, 8MB Flash.

auto-boot: failed, "no such file"

Booting "c800-y6-mw.120-5.T" ...,
              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) C800 Software (C800-Y6-MW), Version 12.0(5)T,  RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Fri 23-Jul-99 01:30 by kpma
Image text-base: 0x000E9000, data-base: 0x00595000

Cisco C803 (MPC850) processor (revision 1) with 43112K bytes of virtual memory.
Processor board ID <pre-production>
CPU part number 33
Bridging software.
Basic Rate ISDN software, Version 1.1.
1 Ethernet/IEEE 802.3 interface(s)
1 ISDN Basic Rate interface(s)
4M bytes of physical memory (DRAM)
8K bytes of non-volatile configuration memory
8M bytes of flash on board (4M from flash card)


         --- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]:
0
 
LVL 18

Expert Comment

by:chicagoan
ID: 8063549
Say NO. Examine your config by logging in, enter the ENABLE command. Do a show flash command to see what IOS image you have in flash.

You should see something like c800-y6-mw.120-5.bin

Now do a show running-config and see what your
boot system flash command says, it should be the same"
boot system flash c800-y6-mw.120-5.bin

0

Featured Post

Free Tool: Site Down Detector

Helpful to verify reports of your own downtime, or to double check a downed website you are trying to access.

One of a set of tools we are providing to everyone as a way of saying thank you for being a part of the community.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

In the hope of saving someone else's sanity... About a year ago we bought a Cisco 1921 router with two ADSL/VDSL EHWIC cards to load balance local network traffic over the two broadband lines we have, but we couldn't get the routing to work consi…
How to set-up an On Demand, IPSec, Site to SIte, VPN from a Draytek Vigor Router to a Cyberoam UTM Appliance. A concise guide to the settings required on both devices
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses

771 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question